SLRM312300BCBDFG datasheet, PDF

Datasheet> All Categories > Passive components> The resistor> SLRM312300BCBDFG

SLRM312300BCBDFG: DescriptionArray/Network Resistor, Isolated, Thin Film, 0.1W, 123ohm, 0.2% +/-Tol, -50,50ppm/Cel, 1521,; CategoryPassive components The resistor; File Size233KB，3 Pages; ManufacturerVishay; Websitehttp://www.vishay.com; Environmental Compliance

Download Datasheet Parametric View All

SLRM312300BCBDFG Overview

Array/Network Resistor, Isolated, Thin Film, 0.1W, 123ohm, 0.2% +/-Tol, -50,50ppm/Cel, 1521,

SLRM312300BCBDFG Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	722880563
Reach Compliance Code	unknown
ECCN code	EAR99
structure	Single Layer
JESD-609 code	e4
Network Type	Isolated
Number of terminals	6
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
Package height	0.64 mm
Package length	3.84 mm
Package form	SMT
Package width	5.37 mm
Rated power dissipation(P)	0.1 W
resistance	123 Ω
Resistor type	ARRAY/NETWORK RESISTOR
series	SLR
size code	1521
technology	THIN FILM
Temperature Coefficient	-50,50 ppm/°C
Terminal surface	Gold (Au) - with Nickel (Ni) barrier
Tolerance	0.2%

SLRM312300BCBDFG Preview

SLR

Vishay Electro-Films

Single Layer Resistor Carrier Networks

FEATURES

•

Standard sizes 0.100, 0.150, 0.210 wide

•

Custom sizes up to 0.500 inches x 0.500 inches

•

Pad count to 36

Product may not

be to scale

•

Mixed values to 500 kΩ

•

Multiple reference resistor groups

•

Ratio tolerance to ± 0.01 %

•

Ratio TCR’s to ± 1 ppm/°C

•

Nichrome resistor material standard. Tantalum nitride

available, consult factory

•

Custom pad spacing 0.025 inches or greater

SLR (Single Layer Resistor Carrier) networks are offered to provide the user with a leadless device that maximizes board density

while maintaining tight ratio tolerances and TCR tracking. Pads are provided top and bottom connected by edge castellations for

ease of visual solder joint inspection. Resistors can be covered with Vishay Electro-Films (EFI) proprietary thermal set plastic

for physical protection or left uncoated to facilitate user trimming.

SLR’s are provided with 0.050 inches standard contact spacing; however, 0.025 inches contact spacing is also available. The

standard contact metallization is gold flash over nickel plate. Solder coated contacts can be provided if preferred. Custom

configurations, values, and tolerance combinations are available with fast turnaround.

PRODUCT CAPABILITIES

Resistance Range

Absolute Resistance Tolerance

Resistance Ratio Tolerance

Absolute TCR

Ratio TCR

Absolute Resistor Stability (Mean)*

Ratio Resistor Stability (Mean)*

Package Power Dissipation

Temperature Range

to 500 kΩ

± 1 % to ± 0.05 %

± 0.1 % to ± 0.01 %

± 50 ppm/°C; available to ± 10 ppm/°C

± 5 ppm/°C; available to ± 1 ppm/°C

300 ppm/1000 hours at 125 °C (typical)

18 ppm/1000 hours at 125 °C (typical)

100 mW/Res at 70 °C, 50 mW/125 °C

0 °C to + 70 °C, - 40 °C to + 85 °C, - 55 °C to + 125 °C

The SLR construction allows for a wide selection of special sizes and shapes with rapid turnaround and low NRE costs. The holes

for the edge castellations are laser drilled into a multiple-up, large area substrates in-house prior to metallization. This permits

new configurations with only laser software and a mask set.

Custom parts can be provided with combinations of features listed:

Any combination of resistor values between 100

and 100 kΩ in the standard sizes.

Custom resistor network patterns (no crossovers).

A wide variety of rectangular sizes and shapes with contact pads on two to four sides.

Pad center-to-center spacings from 0.025 inches (0.635 mm) and larger.

Uncoated to permit customer trimming.

PACKAGED

PRODUCTS

NETWORKS

Document Number: 61068

Revision: 09-Mar-07

For technical questions, contact: efi@vishay.com

www.vishay.com

131

SLR

Vishay Electro-Films

OUTLINE DRAWING

DIMENSIONS

in inches [millimeters]

Single Layer Resistor Carrier Networks

Centers

0.025

[0.64]

0.050

[1.28]

0.100

[2.54]

0.100

[2.54]

0.150

[3.84]

0.210

[5.37]

0.015

[0.38]

0.030

[0.76]

0.030

[0.76]

0.030

[0.76]

0.025

[0.64]

0.050

[1.28]

0.050

[1.28]

0.050

[1.28]

0.015

[0.38]

0.015

[0.38]

0.025

[0.64]

0.025

[0.64]

0.020

[0.51]

0.020

[0.51]

0.020

[0.51]

0.020

[0.51]

0.050

[1.28]

0.050

[1.28]

PIN 1

* 0.025 inches [0.64 mm] per resistor, 2 to 18 pads.

** 0.050 inches [1.28 mm] per resistor, 2 to 18 pads.

Resistor

Area

Single Layer 16 Pin Chip Carrier

Chip measures 0.300 inches x 0.300 inches.

Castellations are on 0.050 inches (1.27 mm) centers.

(Special Order)

Standard Pitch: Castellations are

on 0.050 inches (1.27 mm) centers

(0.025 inch pitch special order)

ORDERING INFORMATION

Example: SLRC-4-10000-1-B-F-D-C-G, 8 Lead 0.100 wide, with 4 Identical 100 kΩ Isolated Resistors, Absolute Tolerance: 0.1 %, Ratio

Tolerance: 0.1 %, Absolute TCR: 50 ppm/°C, Ratio TCR: 2 ppm/°C, Gold Termination

SLR

MODEL

WIDTH

10 000

NUMBER

RESISTANCE

VALUE

ABSOLUTE

VALUE

MULTIPLIER TOLERANCE

RESISTORS

ALL SAME

VALUE

(5 Significant

Digits)

= 0.001

= 0.01

= 0.1

= 1.0

= 10.0

= 100.0

= 0.05

= 0.1

= 0.2

= 0.5

= 1.0

= 2.0

= 5.0

= 10.0

= 20.0

RATIO

TOLERANCE

ABSOLUTE TCR. RATIO TCR TERMINATION

PPM/°C

= 100

= 150

= 210

PACKAGED

PRODUCTS

NETWORKS

(To R1)

= 0.005

= 0.010

= 0.025

= 0.050

= 0.100

= 0.250

= 0.500

= 1.000

= N/A

= 10

= 25

= 50

= 100

= 10

= N/A

= Ni/Gold

= Solder

Coated

NOTE:

Factory will covert order number into final part number.

For special value combinations and pin outs consult Application Engineer

www.vishay.com

132

For technical questions, contact: efi@vishay.com

Document Number: 61068

Revision: 09-Mar-07

Legal Disclaimer Notice

Vishay

Disclaimer

All product specifications and data are subject to change without notice.

Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf

(collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein

or in any other disclosure relating to any product.

Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any

information provided herein to the maximum extent permitted by law. The product specifications do not expand or

otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed

therein, which apply to these products.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this

document or by any conduct of Vishay.

The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless

otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such

applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting

from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding

products designed for such applications.

Product names and markings noted herein may be trademarks of their respective owners.

Document Number: 91000

Revision: 18-Jul-08

www.vishay.com

More (Only the first 5 pages are displayed. Please Download Datasheet to view the full content.) >

Recommended Resources

Dole brand BD-360A, BD-220A, BD-145A, B type refrigerator circuit

Gas, smoke detector circuit diagram B

Multifunctional power socket circuit

Polarity inverting regulator circuit diagram composed of LT1054

TTL to MOS driver

555 novel long timing circuit

[Nucleo experience] + Serial port DMA, I2C read MPU6050: [i=s] This post was last edited by ketose on 2014-10-17 09:04 [/i] I got the development board for a while and read the information. It is too simple to use the mbed platform, but the mbed package is ...; ketose stm32/stm8

Newbie Question: I'm new to Linux drivers. What does ssize_t retval=-ENOMEM mean? Why do we need to do this?...; xiongyi6 Embedded System

Chat wince, share the points!: ~~~~~~~~~~~~~~~~~~~~In two days, it will be exactly nine months since I started using WinCE~~~~~~~~~~~~~~~I feel dizzy. Now I have a few questions, and everyone is welcome to discuss. 1. What city is ...; stone8304 Embedded System

[Help] How to debug a program in falsh (ccs3.3)?: I am a novice, the program is burned in, and it runs normally when the emulator is unplugged.I want to know how to debug the program in Flash (such as setting breakpoints, single-stepping, and other f...; franklin Microcontroller MCU

WinCE5.0 device, with the hardware sound card model changed, *.reg "I2SCodec" from 4228 to 4271, then build and sysgen, the result: the touch screen does not: The original Wince5.0 device was hardware sound card 4228, but later changed to 4271, and the system volume adjustment failed. So I changed all the places involving 4228 in *.reg to 4271, as follows: ...; Nicjwwhg Embedded System

Show the process of WEBENCH design + boost power supply: 1. Open WEBENCH2 Select power supply, output conditions3 Select PART4. Select the solution from the LIST below5. Design completed, output various files...; samhuang8204 Analogue and Mixed Signal

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components