X40035S14-B datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > accessories> X40035S14-B

Preview

X40035S14-B: Description3-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO14; Categoryaccessories; File Size336KB，24 Pages; ManufacturerIntersil ( Renesas ); Websitehttp://www.intersil.com/cda/home/

Download Datasheet View All

X40035S14-B Overview

3-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO14

Preview

Download Datasheet

View All

X40030, X40031, X40034, X40035

Data Sheet

August 25, 2008

FN8114.2

Triple Voltage Monitor with Integrated

CPU Supervisor

The X40030, X40031, X40034, X40035 combine power-on

reset control, watchdog timer, supply voltage supervision,

second and third voltage supervision, and manual reset, in one

package. This combination lowers system cost, reduces board

space requirements, and increases reliability.

Applying voltage to V

activates the power-on reset circuit,

which holds RESET/RESET active for a period of time. This

allows the power supply and system oscillator to stabilize

before the processor can execute code.

Low VCC detection circuitry protects the user’s system from

low voltage conditions, resetting the system when VCC falls

below the minimum VTRIP1 point. RESET/RESET is active

until VCC returns to proper operating level and stabilizes. A

second and third voltage monitor circuit tracks the unregulated

supply to provide a power fail warning or monitors different

power supply voltage. Three common low voltage

combinations are available, however, Intersil’s unique circuits

allows the threshold for either voltage monitor to be

reprogrammed to meet specific system level requirements or to

fine-tune the threshold for applications requiring higher

precision.

Features

• Triple voltage detection and reset assertion

- Standard reset threshold settings; see Table 1 on

page 5.

- Adjust low voltage reset threshold voltages using

special programming sequence

- Reset signal valid to V

= 1V

- Monitor three separate voltages

• Fault detection register

• Selectable power-on reset time-out (0.05s, 0.2s, 0.4s,

0.8s)

• Selectable watchdog timer interval (25ms, 200ms, 1.4s or

off)

• Debounced manual reset input

• Low power CMOS

- 25µA typical standby current, watchdog on

- 6µA typical standby current, watchdog off

• 400kHz 2-wire interface

• 2.7V to 5.5V power supply operation

• Available in 14 Ld SOIC and 14 Ld TSSOP packages

• Monitor voltages: 5V to 0.9V

• Independent core voltage monitor

• Pb-free available (RoHS compliant)

Applications

• Communication equipment

- Routers, hubs, switches

- Disk arrays, network storage

• Industrial systems

- Process control

- Intelligent instrumentation

• Computer systems

- Computers

- Network servers

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.

1-888-INTERSIL or 1-888-468-3774

Intersil (and design) is a registered trademark of Intersil Americas Inc.

All other trademarks mentioned are the property of their respective owners.

Recommended Resources

DC voltage converter circuit schematic diagram

Power line carrier remote alarm circuit diagram

Adjustable voltage regulator from zero volts

OM387B type circuit

Inductive anti-theft alarm

Computer motherboard circuit diagram 815 5_01

Does anyone have the schematic diagram of LPC1227 LPCXpresso?: The LPC1227 LPCXpresso I applied for arrived today... I want to see the schematic... Do you have any... Newbies?...; dsp_yuer NXP MCU

How to compile a C file into a SYS file? Mine is XP DDK.: How to compile a C file into a SYS file? My DDK is XP, installed in C:\WINDDK\2600....; mshop Embedded System

Regarding the problem of voltage regulator chip, I hope experts can help: I made a device with 430, and used UART, keyboard and display as pins. Now I am making a power circuit. How should I choose the voltage regulator chip? How should I design the power circuit with a 3V ...; 近猪者痴xp Microcontroller MCU

How can DIODE confirm whether the patch is pasted upside down during inspection?: How do you check if the DIODE is mounted upside down during actual patch inspection? How do you check? Also, does the inductor have a positive and a negative side?...; 小太阳yy Switching Power Supply Study Group

The use of uln2803!!: First of all, I wish all my friends a happy new year!!Let's get down to business: In the past few days, I made another 3-inch common anode digital display board. I use P1 port to drive uln2803 as the ...; lalaone MCU

Moderator, I would like to ask about the problem of initializing the bss segment of the ST7 startup file?: Hello, moderator. I am using ST72324, STVD4.1.1, COSMIC compiler. When compiling the program, I found that the data in the bss segment was not initialized to 0, but only the zero page was initialized....; mbb stm32/stm8

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components