Contact Resistance Variation ...........................±1 % .................................................................±3 % of total resistance or 3 ohms
(whichever is greater)
Dielectric Withstanding Voltage (MIL-STD-202, Method 301)
Total Resistance Shift ................................... ±10 % maximum ................................................ ±3 % maximum
Rotational Life (No Load) ................................... 100,000 cycles ................................................... 20,000 cycles
Total Resistance Shift ................................... ±15 % TRS maximum ....................................... ±5 % or 5 ohms TRS whichever is greater
Torque (Starting and Running)..................................................................................... A & B bushings 0.35 to 4.23 N-cm (0.05 to 6.0 oz.-in.)
C & E bushings 0.21 to 4.23 N-cm (0.3 to 6.0 oz.-in.)
3856 – 0.11 to 2.12 N-cm (0.15 to 3.0 oz.-in.)
Mounting (Torque on Bushing) ........................................................................................................... 1.7-2.0 N-m (15-18 lb.-in.) maximum
Weight (Single Section) ......................................................................................................................................................30 grams maximum
Terminals ................................................................................................................................................ Printed circuit terminals or solder lugs
Soldering Condition ............................................Recommended hand soldering using Sn95/Ag5 no clean solder, 0.025 ˝ wire diameter.
Maximum temperature 399 °C (750 °F) for 3 seconds. No wash process to be used with no clean flux.
Part can be wave soldered at 260 °C (500 °F) for 5 seconds, no wash process with no clean flux.
Marking...........................................................................Manufacturer’s trademark, wiring diagram, resistance, date code, and part number
Ganging (Multiple Section Potentiometers) ..............................................................................................................................1 cup maximum
Hardware.................................................................................... One lockwasher and one mounting nut is shipped with each potentiometer;
locking bushing versions are shipped with one additional locking nut
specifications tested at 250 RPM, at room ambient: +25 °C nominal.
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
3851/3852/3856 – 3/4 ˝ Diameter Panel Control
Product Dimensions
9.53
(.38)
.38
(.015)
12.7, 22.23
STD.
(1/2, 7/8)
3/8-32 UNEF
.25
45
°
X
(.010)
CHAMFER
6.35+.03/-.05
DIA.
(.250+.001/-.002)
SHAFT SLOT
1.19
.047 WIDE X
1.60+.38/.00
DEEP
(.063+.015/-.000)
6.35
±
.76
(.25
±
.03)
12.7
(.50)
.38
(.015)
15.88
STD.
(5/8)
3/8-32 UNEF
.25
45
°
X
(.010)
CHAMFER
6.35+.03/-.05
DIA.
(.250+.001/-.002)
SHAFT SLOT
1.19 WIDE X
(.047)
1.60+.38/-.00
(.063+.015/-.000)DEEP
6.35
±
.76
(.25
±
.03)
19.05
(.75)
DIA.
12.19
DIA.
(.480)
19.05
(.75)
DIA.
12.19
DIA.
(.48)
SOLDER LUG TERMINAL
6.35
2.79
(.25)
TYP.
(.110)
3 PLCS.
12.7
(.50)
EACH TERMINAL LUG
2
3
2 PLCS.
1
WILL ACCOMMODATE
.72
THREE
(.028)
DIAMETER
14.02
±
.25
(.724 DIA. AWG
(.552
±
.010)
STRANDED) WIRES.
STANDARD
PRINTED CIRCUIT TERMINAL
1.02
6.35
TYP.
TYP.
(.040)
(.25)
15.88
±
.38
(.625
±
.015)
16.00
5.49
OPTIONAL FLAT
(.63)
(.216)
1.52
28.58
LONG OR
FRONT BUSHING FOR SHAFTS UNDER
(.06)
(1-1/8)
1
2
3
6.35
(.25)
6.35
(.25)
9.53, 22.23
STD.
(3/8, 7/8)
.38
(.015)
2.36
(.094)
1/4-32 UNEF
.25
45
°
X (.010)
CHAMFER
6.35
±
.76
(.25
±
.03)
9.53
(.38)
.38
(.015)
12.7
STD.
(1/2)
1/4-32 UNEF
.25
45
°
X (.010)
CHAMFER
6.35
±
.76
(.25
±
.03)
SUGGESTED BOARD LAYOUT
6.35
6.35
(.25)
(.25)
1.40
DIA.
(.055)
19.05
(.75)
DIA.
12.19
DIA.
(.480)
19.05
(.75)
DIA.
3.18
±
0.25
DIA.
(.125
±
.001)
3.18
±
.025
DIA.
(.125
±
.001)
SHAFT SLOT
.79 WIDE X .76 DEEP
(.031)
(.03)
.25
OPTIONAL FLAT
LONG OR
(.010)
1.52
15.88
FRONT BUSHING FOR SHAFTS UNDER
(.06)
(5/8)
SHAFT SLOT
.79 WIDE X .76 DEEP
(.03)
(.031)
12.19
DIA.
(.480)
A, B & H BUSHINGS
9.53
(.375)
C & E BUSHINGS
9.53
(.375)
9.91
DIA.
(.390)
3.18
DIA.
(.125)
3.18
6.73
DIA.
(.125)DIA.
(.265)
9.53
(.38)
6.35
±
.76
(.25
±
.03)
12.7
(.50)
.38
(.015)
6.35+.03/-.05
DIA.
(.250+.001/-.002)
3/8-32 UNEF
1.19
(.047)
9.53
(.38)
6.35
±
.76
(.25
±
.03)
.38
(.015)
12.7
(.50)
6.35+.03/-.05
DIA.
(.250
±
.03)
3/8-32 UNEF.
.79
(.031)
SHAFT SLOT
ALIGNMENT
AT CCW
FLAT
ALIGNMENT
AT CCW
50
° ±
10
°
50
° ±
10
°
19.05
(.75)
DIA.
12.19
DIA.
(.480)
1.60+3.81/-.000
(.063+.015/-.000)
DIA.
22.23
STD.
(7/8)
19.05
(.75)
DIA.
12.19
DIA.
(.480)
.79
±
.25
(.031
±
.010)
22.23
STD.
(7/8)
3.18
±
.03
(.125
±
.003)
DIA.
.25
45
°
X (.010)
CHAMFER
2.67
±
.381
(.105
±
.015)
ANTI-ROTATION LUG
PROJECTS 1/16 INCH
ABOVE MOUNTING FACE.
TOLERANCES EXCEPT AS NOTED:
.127
.XX
±
.38
DECIMALS: .XXX
±
(.005),
(.015)
FRACTIONS:
±
1/64
ANGLE:
±
3 %
.25
45
°
X (.010)
CHAMFER
DIMENSIONS:
MM
(INCHES)
CCW
1
3
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
POTENTIOMETER
2
3851/3852/3856 – 3/4 ˝ Diameter Panel Control
Hardware
LOCKWASHER H-37-1
6.6
(.26)
NUT H-38-1
9.53 +0/-0.38
(.375 +0/-.015)
2.36 ± 0.25
(.093 ± .01)
LOCKNUT H-38-3
4.57 ± 0.05
(.180 ± .002)
7.75
(.305)
11 +0/-0.43
(.433 +0/-.017)
NUT H-38-2
2.36 ± 0.25
(.093 ± .01)
30 ° ± 5 °
1.02
(.040)
30 ° ± 5 °
TYP.
0.64
(.025)
15 ° ± 1 °
1/4-32 UNEF
1/4-32
NEF-20
12.07 ± 0.25
(.475 ± .01)
LOCKWASHER H-37-2
9.58 ± 0.36
(.377 ± .014)
0.64 ± 0.05
(.025 ± .002)
7.92
(.312)
3/8-32 NEF-2B
3.96
(.156)
12.52 ± 0.36
(.493 ± .014)
0.56 ± 0.05
(.022 ± .002)
14.66 +0/-0.43
(.577 +0/-.017)
30 ° ± 5 °
Date Code Description
YYWWM
M = COUNTRY OF MANUFACTURE
(MEXICO)
WW = WEEK NUMBER
YY = LAST TWO DIGITS OF YEAR
MANUFACTURED
DIMENSIONS:
MM
(INCHES)
LOCKNUT H-38-4
8.51 ± 0.05
(.335 ± .002)
1.91
MIN.
(.075)
18 ° ± 2 °
3/8-32
NEF-2B
1.02
(.040)
12.7
(.5)
1.14 ± 0.38
(.045 ± .015)
30 ° ± 5 ° TYP.
4.83
(.19)
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
3851/3852/3856 – 3/4 ˝ Diameter Panel Control
How To Order
3852
A
-
28
2
-
103
A
L
12
16
16
20
28
28
SHAFT TYPE
(FMS) & DIAMETER
3/8 ” (9.53 mm) L X 1/8 ” (3.18 mm) D
1/2 ” (12.7 mm) L x 1/4 ” (6.35 mm) D
1/2 ” (12.7 mm) L x 1/8 ” (3.18 mm) D
5/8 ” (15.88 mm) L X 1/4 ” (6.35 mm) D
7/8 ” (22.20 mm) L X 1/4 ” (6.35 mm) D
7/8 ” (22.20 mm) L X 1/8 ” (3.18 mm) D
AVAILABLE ONLY IN
MODELS
3851, 3852
3851, 3852
3851, 3852
3851, 3852
3851, 3852
3856
3851, 3852
3856
BUSHINGS
C
A
C, E
A, B
A, B
A
C, E
H
Consult factory for lengths not shown.
A
B
C
E
H
BUSHING
Plain 3/8 ” (9.53 mm) D x 3/8 ” (9.53 mm) L
Locking 3/8 ” (9.53 mm) D x 1/2 ” (12.7 mm) L
Plain 1/4 ” (6.35 mm) D x 1/4 ” (6.35 mm) L
Locking 1/4 ” (6.35 mm) D x 1/2 ” (12.7 mm) L
Plain 3/8 ” (9.53 mm) D x 3/8 ” (9.53 mm) L
APPLICABLE MODELS
3851, 3852, 3856
3851, 3852
3851, 3852
3851, 3852
3856 (3.18 mm D Shaft)
RESISTANCE
CODE/VALUE
(IN OHMS)
Model 3851
(102)
1K
(252)
2.5 K
(502)
5K
(103)
10 K
(253)
25 K
(503)
50 K
(104)
100 K
(254)
250 K
(504)
500 K
(105)
1M
Models 3852/3856
(101)
100
(251)
250
(501)
500
(102)
1K
(252)
2.5 K
(502)
5K
(103)
10 K
(253)
25 K
(503)
50 K
(104)
100 K
(254)
250 K
(504)
500 K
(105)
1M
ELEMENT
TAPER/TOLERANCE
A
Linear ±10 %
B
Linear ±20 %
C
Audio CW ±10 %
D
Audio CW ±20 %
E
Linear ±10 %
F
Audio CCW ±10 %
G
Audio CCW ±20 %
H
Linear ±5 %
RoHS IDENTIFIER
L
Compliant
MODEL
3851 3/4 ” (19.05 mm) D Single-Turn C.P.
3852 3/4 ” (19.05 mm) D Single-Turn Cermet
3856 3/4 ” (19.05 mm) D 3-3/4-Turn Cermet
TERMINAL STYLE AND
SHAFT TYPE
1
2
3
5
6
7
Solder Lugs, Plain End
Solder Lugs, Slotted End
Solder Lugs, Flatted Shaft
PC Pins, Plain End
PC Pins, Slotted End
PC Pins, Flatted Shaft
Boldface features are Bourns standard options.
All others are available with higher minimum order
quantities.
APPLICABLE
MODELS
3852, 3856
3851
3852, 3856
3851
3851
3852, 3856
3851
3852, 3856
Asia-Pacific:
Tel: +886-2 2562-4117 • Email: asiacus@bourns.com
EMEA:
Tel: +36 88 885 877 • Email: eurocus@bourns.com
The Americas:
Tel: +1-951 781-5500 • Email: americus@bourns.com
www.bourns.com
REV. 10/20
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
Capacitors are one of the most commonly used components in electronic design. So what role do capacitors play in circuits?[b]1. Bypass capacitors[/b][p=19, null, left][color=#222222][font=Helvetica,]T...
I wrote a CPLD program by myself and wanted to use modelsim to simulate it. So I wrote a testbench file in Quartus, but the error shown above appeared. Please help me. I would be grateful! ! ! ! [/siz...
Specific information can be found on the official website..www.digilent.cn/...or go to the official website of Xilinx...Only pictures are posted below, pictures speak for themselves...If you are inter...
If the ultimate form of a car is a silicon-based life form, then in
the field of
intelligent driving
, it has gradually taken on the appearance of a "veteran driver." In
the field of
the ...[Details]
Flip-chip and ball grid array (BGA) are two widely used packaging technologies in the electronics industry. Each has its own advantages and limitations, and in some cases, they can complement each ...[Details]
In mobile technology, sensors are the primary input for measured signals and form a component of a sensor system. They include sensitive and transducer elements connected to carriers and circuits. ...[Details]
As time goes by, people are increasingly concerned about their own and their families' health. However, existing monitoring devices for individual vital signs have struggled to gain market share du...[Details]
According to foreign media reports, researchers at the University of Surrey have developed an artificial intelligence system that can accurately locate the location of equipment in densely populate...[Details]
According to foreign media reports, BMW has just been granted a patent for a screen that could cover the entire roof. BMW hopes to transform at least a portion of the vehicle's headliner into a dis...[Details]
Linear motor modules have become the "sweet spot" in various fields due to their advantages such as long stroke, fast speed, high precision, smooth operation and long life. Different models of line...[Details]
Shenzhen Baowei Power Supply high frequency pure sine wave power, communication inverter power supply has two communication interfaces, RS232 and R485 interfaces, their functions and characteristic...[Details]
HTTP is the abbreviation of Hypertext Transfer Protocol. It is an application protocol based on TCP/IP communication protocol used to transmit HTML and image files. It is an application-level objec...[Details]
Shanghai, China, August 21, 2025 –
Toshiba Electronic Devices & Storage Corporation (“Toshiba”) today announced the launch of the TLX9161T
, an automotive photorelay in a compact SO12L-T pa...[Details]
The mobile computing market is rapidly evolving, and manufacturers are fiercely competing for market share. A key area of competition is battery life, which encompasses two key aspects: how long th...[Details]
Lithium-ion batteries are a key component of electric vehicles. Their high energy density enables them to store a large amount of energy in a relatively compact and lightweight package, which is cr...[Details]
On August 20, Reuters reported that two sources revealed that U.S. Commerce Secretary Howard Lutnick is exploring the possibility of using CHIPS Act funds in exchange for equity stakes in chip manu...[Details]
Electronics engineers all know that transient voltage suppression (TVS) diodes are used to protect ports, preventing damage to downstream circuits caused by transient voltage surges. In short, TVS ...[Details]
Anyone who has driven a pure electric vehicle will find that it starts much faster than a fuel vehicle. So why do pure electric vehicles start so quickly?
We all know that an engine's to...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
