FMXMC6S2118KJB-08.000000M-TR datasheet, PDF

Datasheet> All Categories > Passive components> Crystal/resonator> FMXMC6S2118KJB-08.000000M-TR

FMXMC6S2118KJB-08.000000M-TR: DescriptionParallel - Fundamental Quartz Crystal, 8MHz Nom, ROHS COMPLIANT, MINIATURE, CERAMIC, SMD, 2 PIN; CategoryPassive components Crystal/resonator; File Size198KB，1 Pages; ManufacturerFrequency Management International; Environmental Compliance

Download Datasheet Parametric View All

FMXMC6S2118KJB-08.000000M-TR Overview

Parallel - Fundamental Quartz Crystal, 8MHz Nom, ROHS COMPLIANT, MINIATURE, CERAMIC, SMD, 2 PIN

FMXMC6S2118KJB-08.000000M-TR Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	1315096736
package instruction	ROHS COMPLIANT, MINIATURE, CERAMIC, SMD, 2 PIN
Reach Compliance Code	compliant
Other features	TR
Ageing	5 PPM/YEAR
Crystal/Resonator Type	PARALLEL - FUNDAMENTAL
Drive level	10 µW
frequency stability	0.005%
frequency tolerance	100 ppm
load capacitance	18 pF
Installation features	SURFACE MOUNT
Nominal operating frequency	8 MHz
Maximum operating temperature	70 °C
Minimum operating temperature	-20 °C
physical size	L6.0XB3.5XH1.1 (mm)/L0.236XB0.138XH0.043 (inch)
Series resistance	60 Ω
surface mount	YES

Preview

Download Datasheet

View All

FMXMC6S2

SERIES

Microprocessor Crystals

Surface Mount Ceramic Pkg.

Miniature 2-Pad / Ultra Thin

High Reliability

Tight Stability

CERAMIC SMD 6x3.5

SPECIFICATIONS

Issue 2 | 07252012

Parameter

Frequency Range

Operation Mode

Load Capacitance (CL)

Frequency Tolerance

Temperature Tolerance

Operating Temperature

Storage Temperature

Equivalent Series Resistance (ESR)

Shunt Capacitance (C0)

Drive Level

Aging @ +25°C

Insulation Resistance

Reflow Conditions

All specifications subject to change without notice.

Specification

8 - 150 MHz

See Operation Mode and ESR Table

18 pF Std, 6 - 60 pF and Series available

±30 ppm @ 25°C Std (See Cal. Tol. for Options)

±50 ppm Std (See Temp. Tol. for Options)

0 to +70°C Std (See Temp. Range for Options)

-40 to +85°C / -55 to +125°C

See Operation Mode and ESR Table

7 pF max

10 µW typical, 300 µW max

±3 ppm typical; ±5 ppm per year max

500MΩ min at 100V

±15V

+260ºC ±10ºC for 10 sec max 2 reflows max

6x3.5 CERAMIC SMD

OPERATION MODE AND ESR TABLE

Frequency (MHz)

8.0 - 13.9

14.0 - 39.0

40.0 - 150.0

Mode

Fundamental

3rd Overtone

Max. ESR (Ohms)

STANDARD MARKING

XXX.XXXM

XXXXXXX

FMI YYWW

XXX.XXXM FREQUENCY in MHz

XXXXXXX Part Number

FMI, Date Code

Recommended Solder Pad Layout

NOTE: Standard Specifications for product indicated in

color

Dimensions:

Inches

(mm)

PART DESCRIPTION SYSTEM

MARKING: See Page 52, Format A

FMXM C6S2 1 18 H J A - XX.XXXXXXM - CM

Product Family

MicroP Crystal

Package

Ceramic SMD

6x3.5mm, 2 pad

Mode

1 - Fundamental

3 - 3rd Overtone

Load Cap. (CL)

18 - Standard (pF)

00 - Series

XX - Custom (pF)

Cal. Tol. @ 25°C

D ±10 ppm

F ±20 ppm

H ±30 ppm

J ±50 ppm

K ±100 ppm

X Custom

Frequency (MHz)

Temp. Range

A 0 to 70 °C

B -20 to 70 °C

C -40 to 85 °C

D -10 to 50 °C

E -10 to 60 °C

F -30 to 60 °C

J 0 to 50 °C

X Custom

Options

TR - Tape & Reel

PD - Parameter Data

TD - Temp. Data

TG - Temp. Grading

CM - Custom Mark

BLANK - None Req’d.

Temp. Tol.

D ±10 ppm

F ±20 ppm

H ±30 ppm

J ±50 ppm

K ±100 ppm

X Custom

1-800-800-XTAL

[9825]

www.fmi-inc.com

Recommended Resources

Monostable flip-flop practical circuit d

Coil short circuit wiring diagram b when released

Calculate the equivalent circuit of H parameters

IC-1431 silicon piezoresistive pressure sensor classic circuit

The most practical basic diagram circuit 32 - dynamic light-controlled AC switch circuit

555 fully automatic home appliance protector circuit

New trends at the Beijing 2008 Security Exhibition --- 3: 3. The concept of "safe city" has become a hot topic in the surveillance industry in the new era. In addition to the trend of networking, wireless and wired combination, and high-magnification lenses,...; ssbrida Industrial Control Electronics

Removing the default pull-up resistor makes the ADC more accurate.: By default, after LPC111x is reset, the pull-up resistor is enabled. This internal pull-up resistor is very convenient when using interfaces such as SSP, and can provide about 50~60uA of pull-up curre...; elulis NXP MCU

Intelligent car information playback system 6: Intelligent car information playback system 6...; zhshmzd123654 Automotive Electronics

I already have the files abc.inf and abc.sys. How can I use wise to package the driver?: I have read the reference manual, but still can't find the method. I already understand the basic usage, but I am not very clear about how to use the inf. The operations that have been completed so fa...; weiyujuan Embedded System

Please advise on the reading and writing problem of 6416 and FIFO connection: My 6416 board has a FIFO connected to CE2 of EMIFB, 15nsCE2 chip select is used as the read signal of FIFO.The read clock of FIFO is ECLKOUT2, which is set to half of the EMIF input clock.Whenthe syst...; eris2007 DSP and ARM Processors

USART2 Interrupts: How to enable the receive empty interrupt of USART2 I'm leaving if I can't handle the emergency help - -!The interrupt function entry has been set in the startup file Can I just write it in stm32f10x_...; duzhiming stm32/stm8

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components