SFN08A8251CLLF

For STM32, there are two ways to reset the software:   1) Use the official software library     The system reset function is directly provided in the stm32f10x_nvic.c file of the official software li...[Details]

     The day before yesterday, I learned about STM's Systick and found it quite useful for precise timing. When I used CVAVR before, I found that the delay.h in it was very useful. So, I used STM32's...[Details]

I used STM32CubeMX V4.22.1 to generate a project including EHT and Lwip. The debugging has been abnormal. After careful inspection, the following problems were found: 1. The hardware uses LAN8720A, b...[Details]

LAN8720 configuration:  IP: 192.168.192.30  Gateway: 192.168.192.1 A high frequency of ARP packets is detected The content of the packet asks for the mac address of 192.168.192.1, and asks the resp...[Details]

As a leading company in automotive semiconductors, Freescale and Khronos Group have jointly launched an automotive multimedia embedded microprocessor i.MX35 with an integrated OpenVG hardware acceler...[Details]

The independent watchdog of STM32 is driven by a dedicated internal 40Khz low-speed clock, that is, it is still effective even if the main clock fails. Here we need to note that the clock of the inde...[Details]

1. Function and purpose         There are two pins BOOT0 and BOOT1 on each STM32 chip. The level status of these two pins when the chip is reset determines which area the program starts from after th...[Details]

#include reg52.h #define PORTLEN P0 sbit bit_select = P2^0; sbit seg_select = P2^1; unsigned char src = {0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,0x7f ,0x6f,0x77,0x7c,0x39,0x5e,0x79,0x71}; unsigne...[Details]

1. A/D (Analog-to-Digital) and D/A (Digital-to-Analog) Conversion 1. Pin AOUT: Analog output Vref: reference voltage AGND: Analog ground EXT: Ground OSC: Floating SCL，SDA：IIC AIN0, AIN1, AIN2: anal...[Details]

Please help me analyze the clock cycles occupied by the following delay program. Seek to explain: DELAY:  MOV  R6, #13 DELAY1: MOV  R5, #250 DELAY2: NOP         DJNZ  R5, DELAY2         DJNZ  R6, DEL...[Details]

//Environment: winavr+avr studio   char temp=0; ISR(TIMER1_COMPA_vect )//interrupt function {     // user code here     temp++;     if (temp==10)     temp=0;     PORTA=temp;     DDRA=0xff; } void ...[Details]

In one of my products, there are two chips, AVR and PIC, at the same time. When AVR drives the relay, then drives the contactor. PIC is used for display. I found that PIC actually has a little interf...[Details]

float ad_value;  float value;  int main( void )  {  WDTCTL=WDTPW+WDTHOLD; //Turn off watchdog  BCSCTL1 =CALBC1_1MHz; //Set DCO to 1MHZ  DCOCTL =CALBC1_1MHZ;  ADC10CTL1=INCH_10; //Select the 10th chan...[Details]

;*********************************************************************** ; Self-receiving photoelectric detection.dt ;***************************************************************************  PORT...[Details]

Recently, the Ericsson Mobility Report pointed out that 5G is expected to be deployed first in dense urban areas to support eMBB (enhanced mobile broadband) services. The report predicts th...[Details]