EEWORLDEEWORLDEEWORLD

Part Number

Search

WBC-T0303AS-07-6980-CG

Description
Array/Network Resistor, Center Tap, Thin Film, 0.25W, 698ohm, 100V, 0.25% +/-Tol, -25,25ppm/Cel, 0303,
CategoryPassive components    The resistor   
File Size376KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance
Download Datasheet Parametric View All

WBC-T0303AS-07-6980-CG Overview

Array/Network Resistor, Center Tap, Thin Film, 0.25W, 698ohm, 100V, 0.25% +/-Tol, -25,25ppm/Cel, 0303,

WBC-T0303AS-07-6980-CG Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid802680603
Reach Compliance Codecompliant
ECCN codeEAR99
structureChip
Network TypeCenter Tap
Number of terminals6
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package length0.762 mm
Package formSMT
Package width0.762 mm
method of packingTray
Rated power dissipation(P)0.25 W
GuidelineMIL-PRF-38534
resistance698 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesWBC(TAPPED)
size code0303
technologyTHIN FILM
Temperature Coefficient-25,25 ppm/°C
Tolerance0.25%
Operating Voltage100 V
Wire Bondable
Chip Resistors
WBC Series
Discrete or tapped schematics
MIL inspection available
High resistor density
IRC Advanced Film Division
IRC’s WBC series wire bondable chip resistors are ideally suited for
the most demanding hybrid application. The WBC combines IRC’s
TaNSil
®
tantalum nitride thin film technology with silicon substrate processing to produce an extremely small
footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil
®
resistor film.
Available in a wide range of tolerances and temperature coefficients to fit a variety of hybrid circuit applica-
tions. Custom resistance values, sizes and schematics are available on request from the factory.
Physical Data
R0202 - Discrete
(0.508mm ±0.025)
0.020˝ ±0.001
Electrical Data
Absolute Tolerance
Absolute TCR
R
Package Power Rating
(@ 70°C)
Rated Operating Voltage
(not to exceed
P x R )
Operating Temperature
Back contact
Noise
Substrate Material
Top contact
Substrate Thickness
Aluminum
Gold
R0202 and
T0303
B0202
Passivation
to ±0.1%
to ±25ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
Oxidized Silicon
(10KÅ SiO
2
min)
0.010˝ ±0.001
(0.254mm ±0.025)
10KÅ minimum
15KÅ minimum
Silicon
(Gold available)
Gold
3KÅ minimum
Silicon Dioxide or
Silicon Nitride
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
B0202 - Discrete back contact
(0.508mm ±0.025)
0.020˝ ±0.001
R
Top contact
pad chamfered
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
T0303 - Tapped network ½R + ½R
Bond Pad
Metallization
(0.762mm ±0.025)
0.030˝ ±0.001
Backside
½R
½R
0.030˝ ±0.001
(0.762mm ±0.025)
0.004˝ min bond pad size
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Email: afdsales@irctt.com • Website: www.irctt.com
A subsidiary of
TT electronics plc
WBC Series Issue April 2006
I would like to ask, what is the range of Wei Kun's AVR oscilloscope?
As title...
forestkeh DIY/Open Source Hardware
About the meaning of the numbers below the HR91105A interface
Recently, I want to use DM9000AEP to make a wired network communication module. When I bought the RJ45 interface HR91105A, I found that there are always 2 sets of numbers (in the form of **/**) under ...
xinsuiwuhen Integrated technical exchanges
Double-sided copper clad
Why are both the top copper and bottom copper connected to GND in a double-sided board? Can't one layer be connected to GND and the other layer to VCC? ? ?...
blm1991k PCB Design
You will understand it after reading it once. It turns out that drawing multi-layer PCB is so easy!
PCB modular layout ideasIn the face of today's electronic products with increasingly higher hardware platform integration and increasingly complex systems, PCB layout should have a modular mindset, re...
btty038 PCB Design
max30003 driver
Has anyone used Maxim's max30003 to detect ECG signals? I use nRF52832 to drive max30003 SPI communication is normal, and the verification is correct by reading the values of other registers that have...
victoria__ Medical Electronics
About the three memory addressing modes of the 240X instruction set
240X addressing modes are divided into three addressing modes: immediate addressing, direct addressing, and indirect addressing. Immediate addressing instructions contain constants as the operands of ...
Jacktang Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 816  808  2194  1672  428  17  45  34  9  46 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号