Today I tried to run the CAN_fifo.c program in the LM3S8962 package and the CAN_device_fifo.c of the LM3S2110. The program ran on the board. I can understand the general functions, but I don't know ho...
This document is a microcontroller tutorial , mainly about the 89C51 microcontroller. The document starts with the basics of microcontrollers, gradually goes into depth, and combines a large number of...
[i=s]This post was last edited by dontium on 2015-1-23 12:59[/i]TI's product portfolio includes all-digital audio components and digital and analog audio solutions, providing high performance and unma...
GSM-based SMS middleware is designed using the .NET platform. Can anyone with practical experience tell me the design steps under the .NET platform (where are the key points)?...
[i=s]This post was last edited by sylar^z on 2019-7-30 17:43[/i]This porting of the X-NUCLEO-IKS01A3 sensor driver is based on the STM8S-DISCOVERY development board, using the official en.x-cube-mems1...
sylar^zST Sensors & Low Power Wireless Technology Forum
When Amazon launched its first
cloud computing
service, the outside world was not optimistic about this direction, as it had high investment, low profits and many uncertainties. Let's follo...[Details]
This is my first time writing an STM32 program. I have many questions to ask. I want to convert the data of the SO of MAX6675 into the actual temperature and read it out using the serial port tool. I...[Details]
On May 16, in response to
the public opinion storm caused by
Lenovo's
"
5G
voting" incident,
Lenovo
Holdings Chairman and
Lenovo
Group Founder Liu Chuanzhi, Lenovo Gr...[Details]
According to the description provided in the official manual of ST, it is not difficult to see that the ADC analog watchdog is actually that the user can set an upper and lower limit of the AD value...[Details]
LiDAR: Autonomous driving from the perspective of optoelectronic technology LiDAR and competing sensor technologies (camera, radar, and ultrasonic) intensify the need for sensor fusion and the need...[Details]
ADI has established long-term good relationships with car manufacturers and Tier 1 component suppliers. Based on its previous long-term successful cooperation with new energy vehicles and suppliers a...[Details]
1) ADC multi-channel acquisition: (Multi-channel acquisition must use scanning mode. In scanning mode, the channels of the rule group share a register, so DMA transmission must be used; to prevent da...[Details]
Note: This STM32 microcontroller is the STM32F103 series. The ADC of Stm32 has DMA function. This is beyond doubt and is what we use most! However, if we want to sample a signal (such as a pulse sign...[Details]
How to convert the pin voltage value into V using the built-in ADC of STM32? V(ADC) = Value(ADC) * V(ref)/4096 (The ADC of STM32 is 12 bits, so the maximum value of the AD word is 4096)
Where V(ADC...[Details]
Use common anode digital tube and independent keyboard to connect P1 and P2 ports of single chip to realize answering machine The procedure is as follows: #include reg52.h void delay(unsigned char n)...[Details]
Assume that both the augend NA and the addend NB are three-byte compressed BCD codes, which are stored in the internal RAM units 20H~22H and 30H~32H, respectively, with the low digit first and the hi...[Details]
1. Analysis of the main causes of AVR damage: The AVR circuit consists of three parts: the rectifier main circuit, the voltage detection circuit, and the comparison control circuit. Excluding the...[Details]
MSP430 MCU 1602 LCD 60-second timing program //************************************************************** // P3BIT5 connects to RS)-- (BIT7 connects to NE)-- (BIT6 connects to RW) //P4 port sends...[Details]