EEWORLDEEWORLDEEWORLD

Part Number

Search

XCCC20685601B

Description
RES NET,THIN FILM,85.6K OHMS,200WV,.1% +/-TOL,-100,100PPM TC,1010 CASE
CategoryPassive components    The resistor   
File Size116KB,3 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

XCCC20685601B Overview

RES NET,THIN FILM,85.6K OHMS,200WV,.1% +/-TOL,-100,100PPM TC,1010 CASE

XCCC20685601B Parametric

Parameter NameAttribute value
Objectid1170270324
package instructionSMT, 1010
Reach Compliance Codeunknown
ECCN codeEAR99
structureChip
Manufacturer's serial numberCCC
Network TypeCenter Tap
Number of terminals6
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height0.25 mm
Package length2.5 mm
Package formSMT
Package width2.5 mm
method of packingTray
Rated power dissipation(P)0.4 W
GuidelineMIL-STD-883
resistance85600 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesCCC
size code1010
Temperature Coefficient-100,100 ppm/°C
Tolerance0.1%
Operating Voltage200 V
CCC
Vishay Electro-Films
Thin Film, 1010 Center-Tapped Resistors on Alumina
CHIP
RESISTORS
FEATURES
Wire bondable
Product may not
be to scale
Larger single size for extended value range
Resistance range total: 100
Ω
to 1 MΩ
Custom values:
R
A
or
R
B
- 50
Ω
to 500 kΩ
Power: 400 mW
Alumina substrate
Low stray capacitance: < 0.2 pF
Resistor material: Nichrome
The CCC series resistor chips offer good 400 mW power, low
shunt capacitance and a center tap feature.
The CCCs nichrome resistor material offers excellent stability.
The CCCs are manufactured using Vishay Electro-Films
(EFI) sophisticated thin film equipment and manufacturing
technology.
The CCCs are 100 % electrically tested and visually
inspected to MIL-STD-883.
APPLICATIONS
Vishay EFI CCC chip resistors provide excellent high-frequency response and are ideally suited for prototyping.
Typical application areas are:
Amplifiers
Couplers
Oscillators
Filters
Attenuators
Recommended for hermetic environment where die is not exposed to moisture.
TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES AND TOLERANCES
Tightest Standard Tolerance Available
0.1 %
± 10 ppm/°C
± 25 ppm/°C
± 50 ppm/°C
± 100 ppm/°C
PROCESS CODE
CLASS H*
203
200
201
202
*MIL-PRF-38534 inspection criteria
CLASS K*
207
204
205
206
100
Ω
200
Ω
500 kΩ
1 MΩ
STANDARD ELECTRICAL SPECIFICATIONS
PARAMETER
Noise, MIL-STD-202, Method 308
Center Tap Ratio,
R
A
/R
B
: Tolerance
Stability, 1000 h, + 125 °C, 400 mW
Operating Temperature Range
Thermal Shock, MIL-STD-202, Method 107, Test Condition F
High Temperature Exposure, + 150 °C, 100 h
Dielectric Voltage Breakdown
Insulation Resistance
Operating Voltage
DC Power Rating at + 125 °C
5 x Rated Power Short-Time Overload, + 25 °C, 5 s
- 20 dB typ.
1±1%
± 0.1 % max.
ΔR/R
- 55 °C to + 125 °C
± 0.25 % max.
ΔR/R
± 0.25 % max.
ΔR/R
400 V
10
12
min.
200 V max.
400 mW max.
± 0.25 % max.
ΔR/R
www.vishay.com
70
For technical questions, contact: efi@vishay.com
Document Number: 61010
Revision: 11-Mar-08
My Shanghai friends advised me not to go to the Expo
Under the strong publicity of the World Expo, I was a little tempted and wanted to take my daughter to broaden her horizons, so I asked a friend in Shanghai. His answer was "a very bad temple fair, no...
向农 Talking
About Duplex Communication
[i=s]This post was last edited by paulhyde on 2014-9-15 08:53[/i] Does anyone have experience with duplex communications? I would like some advice. I plan to use the same antenna for both sending and ...
离落shuling Electronics Design Contest
Basic Electronics Knowledge: What is DSP and DSP Technology Detailed Explanation
Digital Signal Processing (DSP) is an emerging discipline that involves many disciplines and is widely used in many fields. Since the 1960s, with the rapid development of computer and information tech...
jioeio DSP and ARM Processors
AT91SAM9261 EK board schematic (atmel)
Download from foreign websites...
lusongbo DIY/Open Source Hardware
I am looking for a stepper motor acceleration and deceleration control program, a C51 language program for a single-chip microcomputer, and I want to use a timer to implement the acceleration and deceleration control.
It is to allow the stepper motor to have an acceleration process when it starts at a relatively high speed, so as to obtain a relatively high speed. Now it is required to use timer interrupt to comple...
xuxiaoqmm 51mcu
Is the C2000 launchpad first come first served or first 100 people with the highest scores?
[url=https://bbs.eeworld.com.cn/thread-349228-1-1.html]https://bbs.eeworld.com.cn/thread-349228-1-1.html[/url]The first-floor administrator said that the activity method is Article 5, first come first...
ayu_ag Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2789  1746  1166  1252  2685  57  36  24  26  55 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号