EEWORLDEEWORLDEEWORLD

Part Number

Search

EMRC13J2H-28.160MTR

Description
CRYSTAL OSCILLATOR, CLOCK, LVPECL OUTPUT
CategoryPassive components    oscillator   
File Size774KB,10 Pages
ManufacturerECLIPTEK
Websitehttp://www.ecliptek.com
Environmental Compliance
Download Datasheet Parametric View All

EMRC13J2H-28.160MTR Overview

CRYSTAL OSCILLATOR, CLOCK, LVPECL OUTPUT

EMRC13J2H-28.160MTR Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid7039980086
Reach Compliance Codeunknown
Other featuresENABLE/DISABLE FUNCTION; COMPLEMENTARY OUTPUT; TR, 14 INCH
maximum descent time0.5 ns
Frequency Adjustment - MechanicalNO
frequency stability25%
JESD-609 codee4
Installation featuresSURFACE MOUNT
Nominal operating frequency28.16 MHz
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Oscillator typeLVPECL
Output load50 OHM
physical size7.0mm x 5.0mm x 0.85mm
longest rise time0.5 ns
Maximum supply voltage3.63 V
Minimum supply voltage2.97 V
Nominal supply voltage3.3 V
surface mountYES
maximum symmetry55/45 %
Terminal surfaceNickel/Palladium/Gold (Ni/Pd/Au)
Ecliptek | EMRC13 Series Oscillator
http://www.ecliptek.com/oscillators/EMRC13/
Log On
| 714-433-1200 |
Email Customer Support
Home
Products
Quick Quote
My Parts List
Site Map
Contact Us
EMRC13 Series Oscillator
MEMS Clock Oscillators LVPECL (PECL) 3.3Vdc 6 Pad 5.0mm x 7.0mm Plastic Surface Mount (SMD)
2011/65 +
2015/863
168 SVHC
Revision A 05/11/2012
Electrical Specifications
Nominal Frequency
1.000MHz to 625.000MHz
Some frequencies within this range may not be available.
Frequency Tolerance/Stability
(Inclusive of all conditions: Calibration Tolerance at 25°C, Frequency
Stability over the Operating Temperature Range, Supply Voltage
Change, Output Load Change, First Year Aging at 25°C, Reflow, Shock,
and Vibration)
±100ppm Maximum
±50ppm Maximum
±25ppm Maximum
±20ppm Maximum
0°C to +70°C
-20°C to +70°C
-40°C to +85°C
3.3V
DC
±10%
Excluding Load Termination Current
60mA Typical, 70mA Maximum
V
DD
-1.10V
DC
Minimum, 2.40V
DC
Typical, V
DD
-0.70V
DC
Maximum
V
DD
-1.90V
DC
Minimum, 1.60V
DC
Typical, V
DD
-1.50V
DC
Maximum
600mVdc Minimum, 800mVdc Typical, 1000mVdc Maximum
Measured at 50% of waveform
50 ±10(%)
50 ±5(%) (Not available over Nominal Frequency range of
312.500001MHz to 524.999999MHz)
Measured at 20% to 80% of Waveform
300pSec Typical, 500pSec Maximum
50 Ohms into V
CC
-2.0V
DC
LVPECL
Output Enable (OE) and Complementary Output
Vih of 70% of Vdd Minimum or No Connect to Enable Output and
Complementary Output, Vil of 30% of V
DD
Maximum to Disable Output
and Complementary Output (High Impedance)
35mA Maximum (OE) Without Load at Logic Control / Additional
Output of Output Enable (OE) and Complementary Output
Fj = 12kHz to 20MHz; Random
0.5pSec Typical, 1pSec Maximum
0.2pSec Typical
Operating Temperature Range
Supply Voltage (V
DD
)
Input Current
Output Voltage Logic High (V
OH
)
Output Voltage Logic Low (V
OL
)
Output Swing (VOpp)
Duty Cycle
Rise Time/Fall Time
Load Drive Capability
Output Logic Type
Logic Control / Additional Output
Output Control Input Voltage
Output Enable Current
RMS Phase Jitter
Period Jitter (Deterministic)
1 of 10
28-Jan-2016 1:58 PM
Decoding Analysis and Simulation of 315Mhz and 433Mhz Wireless Remote Control Signals
[i=s]This post was last edited by Jacktang on 2019-11-14 23:07[/i]summarySome time ago, while learning radio, I learned that Arduino was a good choice for me after Raspberry Pi as a technical geek wit...
Jacktang RF/Wirelessly
Inductance AND Capacitance Analysis
電感AND電容分析...
安_然 Analog electronics
Asking for advice: MSP430F149 ADC12 measurement error is large
[i=s] This post was last edited by dontium on 2015-1-23 12:55 [/i] Dear experts and moderators, I use MSP430F149 to perform AD sampling. The measured numbers are very different. What is the reason? Fo...
rgqy Analogue and Mixed Signal
Serial port initialization problem during kernel startup--based on Loongson 1 embedded development board
I have a Loongson 1 development board based on Haishan dev3210. When porting it to linux-2.6.22.6, I encountered the problem that the serial port could not be initialized normally, resulting in the in...
Zeltwanger Embedded System
How to design a power supply using lm2576
My graduation project is to make a power supply with an output of positive and negative 12V and an output current greater than 1.5A. I chose lm2576, which can get a positive 12V output. However, pin 2...
smpqdzzhy Power technology
Visiting the "World's No. 1 E-waste Town" - Guiyu, Shantou
[i=s]This post was last edited by jameswangsynnex on 2015-3-3 19:58[/i] [color=black]Author: Emma Lu, Jacky Deng Guiyu, Shantou, is a place of mixed joy and sorrow. Since the early 1990s, electronic w...
wstt Mobile and portable

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1090  721  250  2754  1926  22  15  6  56  39 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号