74AVCH4T245_15 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > 74AVCH4T245_15

Preview

74AVCH4T245_15: Description4-bit dual supply translating transceiver with configurable voltage translation; 3-state; File Size204KB，30 Pages; ManufacturerPhilips Semiconductors (NXP Semiconductors N.V.); Websitehttps://www.nxp.com/

Download Datasheet View All

74AVCH4T245_15 Overview

4-bit dual supply translating transceiver with configurable voltage translation; 3-state

Preview

Download Datasheet

View All

74AVCH4T245

4-bit dual supply translating transceiver with configurable

voltage translation; 3-state

Rev. 4 — 14 December 2011

Product data sheet

1. General description

The 74AVCH4T245 is a 4-bit, dual supply transceiver that enables bidirectional level

translation. The device can be used as two 2-bit transceivers or as a 4-bit transceiver. It

features two 2-bit input-output ports (nAn and nBn), a direction control input (nDIR), a

output enable input (nOE) and dual supply pins (V

CC(A)

and V

CC(B)

). Both V

CC(A)

and

CC(B)

can be supplied at any voltage between 0.8 V and 3.6 V making the device suitable

for translating between any of the low voltage nodes (0.8 V, 1.2 V, 1.5 V, 1.8 V, 2.5 V and

3.3 V). Pins nAn, nOE and nDIR are referenced to V

CC(A)

and pins nBn are referenced to

CC(B)

. A HIGH on nDIR allows transmission from nAn to nBn and a LOW on nDIR allows

transmission from nBn to nAn. The output enable input (nOE) can be used to disable the

outputs so the buses are effectively isolated.

The device is fully specified for partial power-down applications using I

OFF

. The I

OFF

circuitry disables the output, preventing any damaging backflow current through the

device when it is powered down. In suspend mode when either V

CC(A)

or V

CC(B)

are at

GND level, both nAn and nBn outputs are in the high-impedance OFF-state. The bus hold

circuitry on the powered-up side always stays active.

The 74AVCH4T245 has active bus hold circuitry which is provided to hold unused or

floating data inputs at a valid logic level. This feature eliminates the need for external

pull-up or pull-down resistors.

2. Features and benefits



Wide supply voltage range:



CC(A)

: 0.8 V to 3.6 V



CC(B)

: 0.8 V to 3.6 V



Complies with JEDEC standards:



JESD8-12 (0.8 V to 1.3 V)



JESD8-11 (0.9 V to 1.65 V)



JESD8-7 (1.2 V to 1.95 V)



JESD8-5 (1.8 V to 2.7 V)



JESD8-B (2.7 V to 3.6 V)



ESD protection:



HBM JESD22-A114E Class 3B exceeds 8000 V



MM JESD22-A115-A exceeds 200 V



CDM JESD22-C101C exceeds 1000 V



Maximum data rates:



380 Mbit/s ( 1.8 V to 3.3 V translation)

Recommended Resources

Length measurement grouping ladder diagram

Commonly used non-sinusoidal oscillator circuits, waveforms and frequency calculation formulas-sawtooth wave oscillator-using intermittent oscillators

Large drum type washing machine electric controller

High speed monostable circuit

Yikang YW-3B hand warmer circuit diagram

Frequency-Voltage Conversion Circuit

Has anyone used the software every circuit?: Has anyone used the software every circuit? Currently, there is only an Android version for mobile phones, which is not very convenient to use, but the simulation effect is very vivid. If you have a P...; QWE4562009 Integrated technical exchanges

EE_FPGA 2.0 [Soldering Guide] Final Edition: Partial page preview...; chenzhufly FPGA/CPLD

Simple analysis of three-pole and four-pole leakage protectors (transferred): [size=2]Installing a leakage protector in a low-voltage power distribution system is an effective measure to prevent electric shock, and can also prevent electrical fires and equipment damage accident...; wuguo Industrial Control Electronics

The necessity of learning simulation + designing communication isolation!: [i=s]This post was last edited by dontium on 2015-1-23 11:45[/i] If isolation is not used in the design, many unexpected situations will occur when the product is used in a particularly complex enviro...; DavidZH Analogue and Mixed Signal

How to design a multi-channel and multi-range bipolar input signal acquisition system?: This system is: Input: >=4 signal range: multi-range such as +-0.1v, +-0.5v, +-60v Resolution: >=12bit Output: CAN bus sensor multi-level power supply: such as +-5v, +-10v, +-15v I am afraid that only...; hkey Embedded System

Fun little test! Let's start now....: [align=left][color=#000][/color][/align] [align=left][color=#000]Take out a blank sheet of paper. The answers will be at the end, so you can grade yourself. Give it a try! [/color][/align][align=left]...; maylove Analogue and Mixed Signal

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components