EEWORLDEEWORLDEEWORLD

Part Number

Search

WBC-T0303AG-03-7321-DD

Description
Array/Network Resistor, Center Tap, Thin Film, 0.25W, 7320ohm, 100V, 0.5% +/-Tol, -25,25ppm/Cel, 0303,
CategoryPassive components    The resistor   
File Size376KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance
Download Datasheet Parametric View All

WBC-T0303AG-03-7321-DD Overview

Array/Network Resistor, Center Tap, Thin Film, 0.25W, 7320ohm, 100V, 0.5% +/-Tol, -25,25ppm/Cel, 0303,

WBC-T0303AG-03-7321-DD Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid802620044
Reach Compliance Codecompliant
ECCN codeEAR99
structureChip
Network TypeCenter Tap
Number of terminals6
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package length0.762 mm
Package formSMT
Package width0.762 mm
method of packingTray
Rated power dissipation(P)0.25 W
resistance7320 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesWBC(TAPPED)
size code0303
technologyTHIN FILM
Temperature Coefficient-25,25 ppm/°C
Tolerance0.5%
Operating Voltage100 V
Wire Bondable
Chip Resistors
WBC Series
Discrete or tapped schematics
MIL inspection available
High resistor density
IRC Advanced Film Division
IRC’s WBC series wire bondable chip resistors are ideally suited for
the most demanding hybrid application. The WBC combines IRC’s
TaNSil
®
tantalum nitride thin film technology with silicon substrate processing to produce an extremely small
footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil
®
resistor film.
Available in a wide range of tolerances and temperature coefficients to fit a variety of hybrid circuit applica-
tions. Custom resistance values, sizes and schematics are available on request from the factory.
Physical Data
R0202 - Discrete
(0.508mm ±0.025)
0.020˝ ±0.001
Electrical Data
Absolute Tolerance
Absolute TCR
R
Package Power Rating
(@ 70°C)
Rated Operating Voltage
(not to exceed
P x R )
Operating Temperature
Back contact
Noise
Substrate Material
Top contact
Substrate Thickness
Aluminum
Gold
R0202 and
T0303
B0202
Passivation
to ±0.1%
to ±25ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
Oxidized Silicon
(10KÅ SiO
2
min)
0.010˝ ±0.001
(0.254mm ±0.025)
10KÅ minimum
15KÅ minimum
Silicon
(Gold available)
Gold
3KÅ minimum
Silicon Dioxide or
Silicon Nitride
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
B0202 - Discrete back contact
(0.508mm ±0.025)
0.020˝ ±0.001
R
Top contact
pad chamfered
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
T0303 - Tapped network ½R + ½R
Bond Pad
Metallization
(0.762mm ±0.025)
0.030˝ ±0.001
Backside
½R
½R
0.030˝ ±0.001
(0.762mm ±0.025)
0.004˝ min bond pad size
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Email: afdsales@irctt.com • Website: www.irctt.com
A subsidiary of
TT electronics plc
WBC Series Issue April 2006
About FPGA receiving burst data
I am not an FPGA expert, but I have encountered such a problem with FPGA during project development and I would like to ask for advice. When using FPGA serdes to receive burst data (1.25GEPON signal),...
jean_tj FPGA/CPLD
I would like to ask you, how much is the cheapest 2.8 inch 320X240 TFT?
I would like to ask you, what is the cheapest price of a 2.8-inch 320X240 TFT? Thank you!...
zhou.63624 stm32/stm8
Application of observer-based method in three-phase inverter fault diagnosis
In recent years, with the continuous improvement of control theory, research on fault diagnosis of control systems has attracted more and more attention [1][2], and many research results have been ach...
zbz0529 Test/Measurement
What is the difference between multiplicative DA and ordinary DA?
I hope you can explain the difference between multiplication type DA and ordinary DA....
wstt TI Technology Forum
Keil5 software simulation problem
When keil5 software is simulating, I set a breakpoint in the main function, and then click run to try to jump to the breakpoint, but the following situation occursSet the breakpoint at the LED0=1 stat...
反倒是fdsf stm32/stm8
Multi-core DSP Applications in the SoC Era
[i=s]This post was last edited by fish001 on 2018-6-21 21:40[/i] [size=5] One of the most important application areas of multi-core DSP is 3G digital mobile communication. This includes applications i...
fish001 DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 581  1069  205  1973  2271  12  22  5  40  46 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号