WBC-T0303GS-07-8062-FD datasheet, PDF

Datasheet> All Categories > Passive components> The resistor> WBC-T0303GS-07-8062-FD

WBC-T0303GS-07-8062-FD: DescriptionArray/Network Resistor, Center Tap, Thin Film, 0.25W, 80600ohm, 100V, 1% +/-Tol, -25,25ppm/Cel, 0303,; CategoryPassive components The resistor; File Size376KB，3 Pages; ManufacturerTT Electronics plc; Websitehttp://www.ttelectronics.com/; Environmental Compliance

Download Datasheet Parametric View All

WBC-T0303GS-07-8062-FD Overview

Array/Network Resistor, Center Tap, Thin Film, 0.25W, 80600ohm, 100V, 1% +/-Tol, -25,25ppm/Cel, 0303,

WBC-T0303GS-07-8062-FD Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	802763166
Reach Compliance Code	compliant
ECCN code	EAR99
structure	Chip
Network Type	Center Tap
Number of terminals	6
Maximum operating temperature	150 °C
Minimum operating temperature	-55 °C
Package length	0.762 mm
Package form	SMT
Package width	0.762 mm
method of packing	Tray
Rated power dissipation(P)	0.25 W
Guideline	MIL-PRF-38534
resistance	80600 Ω
Resistor type	ARRAY/NETWORK RESISTOR
series	WBC(TAPPED)
size code	0303
technology	THIN FILM
Temperature Coefficient	-25,25 ppm/°C
Tolerance	1%
Operating Voltage	100 V

Preview

Download Datasheet

View All

Wire Bondable

Chip Resistors

WBC Series

•

Discrete or tapped schematics

•

MIL inspection available

•

High resistor density

IRC Advanced Film Division

IRC’s WBC series wire bondable chip resistors are ideally suited for

the most demanding hybrid application. The WBC combines IRC’s

TaNSil

tantalum nitride thin ﬁlm technology with silicon substrate processing to produce an extremely small

footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil

resistor ﬁlm.

Available in a wide range of tolerances and temperature coefﬁcients to ﬁt a variety of hybrid circuit applica-

tions. Custom resistance values, sizes and schematics are available on request from the factory.

Physical Data

R0202 - Discrete

(0.508mm ±0.025)

0.020˝ ±0.001

Electrical Data

Absolute Tolerance

Absolute TCR

Package Power Rating

(@ 70°C)

Rated Operating Voltage

(not to exceed

√

P x R )

Operating Temperature

Back contact

Noise

Substrate Material

Top contact

Substrate Thickness

Aluminum

Gold

R0202 and

T0303

B0202

Passivation

to ±0.1%

to ±25ppm/°C

250mW

100V

-55°C to +150°C

<-30dB

Oxidized Silicon

(10KÅ SiO

min)

0.010˝ ±0.001

(0.254mm ±0.025)

10KÅ minimum

15KÅ minimum

Silicon

(Gold available)

Gold

3KÅ minimum

Silicon Dioxide or

Silicon Nitride

0.004˝ min bond pad size

0.020˝ ±0.001

(0.508mm ±0.025)

B0202 - Discrete back contact

(0.508mm ±0.025)

0.020˝ ±0.001

Top contact

pad chamfered

0.004˝ min bond pad size

0.020˝ ±0.001

(0.508mm ±0.025)

T0303 - Tapped network ½R + ½R

Bond Pad

Metallization

(0.762mm ±0.025)

0.030˝ ±0.001

Backside

½R

0.030˝ ±0.001

(0.762mm ±0.025)

0.004˝ min bond pad size

General Note

IRC reserves the right to make changes in product speciﬁcation without notice or liability.

All information is subject to IRC’s own data and is considered accurate at time of going to print.

• Corpus Christi Texas 78411 USA

Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Email: afdsales@irctt.com • Website: www.irctt.com

A subsidiary of

TT electronics plc

WBC Series Issue April 2006

Recommended Resources

Flash signal light circuit one b

Y-△ started motor automatic mutual switching circuit b

STK433-105 / STK433 power amplifier circuit diagram

sub-audio tone coder

Multifunctional disease detection and automatic treatment period

Computer motherboard circuit diagram 830_42

Help: How to use the calibration formula for the STM32L476 ADC to collect the internal temperature sensor voltage value?: [size=3][backcolor=rgb(239, 245, 249)]How do I use this calibration formula in the conversion formula? [/backcolor][/size][color=#ff00][backcolor=rgb(239, 245, 249)][size=3]What values should TS_CAL1 ...; dianhang stm32/stm8

The sensor on the motorcycle instrument will light up when there is power. What type of diode is used on the circuit board?: Does anyone know what type of glass diode is on the board? It is a sensor used in motorcycle instruments. I have tried many voltage regulators but none of them worked. The light is always on. It says ...; mk651580859 Automotive Electronics

Has anyone used HS mode for stm32F207?: I am debugging the USB communication of STM32F207, using the high-speed mode, and adding an external transceiver USB3300. Have you ever used USB3300? Now I cannot achieve the communication between the...; 小木头人 stm32/stm8

How to set the minimum area of Solid Region in Altium: Double-clicking during the drawing process results in some extremely small solid areas in the editing area. Some solid areas are automatically assigned to networks, and similar thin lines are automati...; 大小家伙好 PCB Design

LIS3DH sensor high-pass filter question and data refresh rate consultation: I am currently debugging the LIS3DH three-axis acceleration sensor and have come across a few issues. I would like to ask the experts about the main application scenarios: I am going to use this senso...; yanghaii MEMS sensors

Anti-collision mechanism for RFID multi-tag reading: Under normal circumstances, an RFID reader can only read or write one RFID card in the magnetic field at a time. However, in actual applications, multiple cards often enter the reader's radio frequenc...; Jacktang RF/Wirelessly

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components