EEWORLDEEWORLDEEWORLD

Part Number

Search

M55342E10B229AVW0

Description
Fixed Resistor, Thin Film, 0.5W, 229ohm, 75V, 0.1% +/-Tol, 25ppm/Cel, Surface Mount, 1010, CHIP
CategoryPassive components    The resistor   
File Size98KB,4 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

M55342E10B229AVW0 Overview

Fixed Resistor, Thin Film, 0.5W, 229ohm, 75V, 0.1% +/-Tol, 25ppm/Cel, Surface Mount, 1010, CHIP

M55342E10B229AVW0 Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid145075038757
package instructionSMT, 1010
Reach Compliance Codenot_compliant
ECCN codeEAR99
Other featuresNON-INDUCTIIVE, LASER TRIMMABLE
structureRectangular
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package height0.254 mm
Package length2.667 mm
Package formSMT
Package width2.54 mm
method of packingWAFFLE PACK
Rated power dissipation(P)0.5 W
Rated temperature70 °C
GuidelineMIL-PRF-55342
resistance229 Ω
Resistor typeFIXED RESISTOR
size code1010
surface mountYES
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Terminal shapeWRAPAROUND
Tolerance0.1%
Operating Voltage75 V
E/H (Military M/D55342)
www.vishay.com
Vishay Dale Thin Film
QPL MIL-PRF-55342 Qualified
Thin Film Resistor, Surface-Mount Chip
FEATURES
• Established reliability, “S” and “V” failure rate level
(10 ppm), C = 2
• High purity alumina substrate
• Wraparound termination featuring a tenacious adhesion
layer covered with an electroplated nickel barrier layer for
+150 °C operating conditions
LINKS TO ADDITIONAL RESOURCES
D
D
3
3
3D Models
• Very low noise and voltage coefficient
(< -25 dB, 0.5 ppm/V)
• Non-inductive
• Laser-trimmed tolerances ± 0.1 %
• Wraparound resistance less than 0.010
typical
• In-lot tracking less than 5 ppm/°C
• Complete MIL-testing available in-house
• Antistatic waffle pack or tape and reel packaging available
• Military / aerospace / QPL
Thin Film Mil chip resistors feature all sputtered wraparound
termination for excellent adhesion and dimensional
uniformity. They are ideal in applications requiring stringent
performance requirements. Established reliability is assured
through 100 % screening and extensive environmental lot
testing.
CONSTRUCTION
Passivation
Resistor Film
Solder
Coating
Nickel Barrier
High Purity
Alumina Substrate
Adhesion Layer
TYPICAL PERFORMANCE
ABSOLUTE
TCR
TOL.
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Resistance Range
TCR: Absolute
Tolerance: Absolute
Stability: Absolute
Stability: Ratio
Voltage Coefficient
Working Voltage
Operating Temperature Range
Storage Temperature Range
Noise
Shelf Life Stability: Absolute
SPECIFICATIONS
Tamelox resistor film (passivated nichrome)
10
to 6.19 M
± 25 ppm/°C to ± 300 ppm/°C
± 0.1 % to ± 10 %
R
± 0.02 %
-
0.1 ppm/V
30 V to 200 V
-55 °C to +150 °C
-55 °C to +150 °C
< - 25 dB
R
± 0.01 %
CONDITIONS
-
-
-55 °C to +125 °C
+25 °C
2000 h at +70 °C
-
-
-
-
-
-
1 year at +25 °C
Revision: 14-May-2020
Document Number: 60018
1
For technical questions, contact:
thinfilm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
How to make an amplifier power supply
[i=s]This post was last edited by paulhyde on 2014-9-15 09:25[/i]I was recently working on a signal amplification project and found that the power supply regulator chips I used before, such as 7805, 7...
linxiaorui Electronics Design Contest
STM32F769I-DISCO development board unboxing experience
[i=s]This post was last edited by waihekor on 2016-12-18 22:31[/i] I applied for the STM32F769I-DISCO, a very high-end development board, some time ago. I would like to thank the staff of the Electron...
waihekor stm32/stm8
20 analog circuits that engineers should master
I have always downloaded from the forum. Today I upload a document I got from another forum. I hope it will be helpful to you. . [size=4]Thanks to the original author! [/size]...
swfc_qinmm Analog electronics
Arm2410: jump to ram? how to? So confused! ! ! ! Help everyone
: The following is a piece of code from ARM boot loader. How is the jump to ram ensured? Is =on_the_ram the starting 'steppingstone' buffer or the address of SDRAM? Please teach me, thank you bl copy_...
abncat ARM Technology
FPGA (V): (Basic || Combinational) Logic
[i=s] This post was last edited by Hai on 2016-3-21 14:56 [/i] [font=微软雅黑][size=4] In the second section, I wrote this sentence: "Any structure comes from simple components and complex logic. FPGA use...
凔海 FPGA/CPLD
Get the first look at the ST SensorTile development kit shortlist
[font=微软雅黑][size=4]Event details: [url]https://bbs.eeworld.com.cn/thread-505966-1-1.html[/url] [/size][/font] [font=微软雅黑][size=4]{:1_102:}Thank you for your attention and application to evaluate the S...
EEWORLD社区 ST Sensors & Low Power Wireless Technology Forum

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1125  85  2824  1746  1800  23  2  57  36  37 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号