EEWORLDEEWORLDEEWORLD

Part Number

Search

2631LP/2A22601L24V/3

Description
Rocker Switch, SPST, Latched, 15A, 12VDC, Solder/quick Connect Terminal, V-shaped Rocker Actuator, Panel Mount
CategoryMechanical and electronic products    switch   
File Size229KB,8 Pages
ManufacturerAPEM
Environmental Compliance
Download Datasheet Parametric View All

2631LP/2A22601L24V/3 Overview

Rocker Switch, SPST, Latched, 15A, 12VDC, Solder/quick Connect Terminal, V-shaped Rocker Actuator, Panel Mount

2631LP/2A22601L24V/3 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Reach Compliance Codecompli
ECCN codeEAR99
Actuator typeV-SHAPED ROCKER
body width18.5 mm
body height28.1 mm
Body length or diameter32 mm
Contact (AC) maximum rated R load16A@250VAC
Maximum contact current (AC)16 A
Maximum contact current (DC)15 A
Contact (DC) maximum rated R load15A@12VDC
Maximum contact voltage (AC)250 V
Maximum contact voltage (DC)12 V
Electrical life10000 Cycle(s)
illuminationRED LAMP
Manufacturer's serial number2600
Installation featuresPANEL MOUNT
Maximum operating temperature125 °C
Minimum operating temperature-20 °C
method of packingBULK
sealDUST PROOF; WATER PROOF
surface mountNO
Switch actionLATCHED
switch functionSPST
Switch typeROCKER SWITCH
Termination typeSOLDER/QUICK CONNECT
Base Number Matches1
2600 series
Illuminated and non-illuminated rocker switches
Distinctive features and specifications
Three rocker shapes : plain, V-shaped or concave
Various rocker colours
Frame with protection guard on 2600LP models
UL, CSA, VDE and NF (EN 61058-1) approved
ELECTRICAL SPECIFICATIONS
• Max. current/voltage rating with resistive load and approved ratings : see table below.
• Initial contact resistance : 10mΩ max. at 1A 2VDC
• Insulation resistance : 1.000 MΩ min. at 500VDC
• Dielectric strength : 2.500 Vrms 50 Hz min. between terminals
3.000 Vrms 50 Hz min. between terminals and metal panel
• Electrical life : 10.000 cycles at full load
APPROVED RATINGS
FUNCTIONS
CSA
CSA 22-2
DIRECT CURRENT
NF
EN 61058-1
UL
UL 1054
VDE
EN 61058-1
24 VDC
12 VDC
D
ON - OFF
ON - ON
1/6 HP 125VAC
16A 125VAC
16A 250VAC
1/3 HP 250VAC
10A 125VAC
10A 250VAC
1/6 HP 125/250VAC
-
10A 125VAC
10A 250VAC
1/6 HP 250VAC
1/6 HP 125VAC
16A 125VAC
16A 250VAC
1/3 HP 250VAC
10A 125VAC
10A 250VAC
1/6 HP 125/250VAC
-
-
10(4)A 250VAC
T 85/55
-
10A
15A
ON - OFF - ON
ON - ON - ON
OTHERS
L I option
10(4)A 250VAC
-
L I option
10(4)A 250VAC
L I option
10(4)A 250VAC
-
L I option
10(4)A 250VAC
8A
5A
8A
10A
8A
10A
MATERIALS
GENERAL SPECIFICATIONS
• Case : melamine/polyester
• Frame : polyamide
• Actuator : polyamide
• Contacts :
A
: silver
C
: copper, silver plated
• Panel thickness : 0,8 mm to 4 mm (.031 to .157)
• Operating temperature :
- silver contacts (A) : -20°C to +125°C
- silver plated contacts (C) : -10°C to +55°C
AGENCY APPROVALS
EN 61058-1
EN 61058-1
Availability
: consult factory for details of approved models.
Marking
: approved models are standard marked.
APEM
www.apem.com
D-49
This effort is still no match for analog circuits? How to achieve flicker-free dimming with a single-chip microcomputer
:funk: I have been busy all day today, and I want to make a flicker-free dimming circuit controlled by a single-chip microcomputer. The picture is as follows:...
ichuangj 51mcu
Why can't falsh boot normally after powering on again?
The flash is programmed and works fine as long as the power is on, but it stops working as soon as the power is off. What is the reason?...
cnnbxc Analogue and Mixed Signal
FPGA learning DS1302 clock + digital tube display
[i=s]This post was last edited by gurou1 on 2017-5-14 14:52[/i] [font=楷体, 楷体_GB2312][size=5]1. Experimental purpose: Understand the working principle of DS1302 and display the hours, minutes and secon...
gurou1 FPGA/CPLD
Recommend a TI product replacement website
There is a very concise and general introduction to TI's controller products, and there are many reference solutions using this as the entry point, which is very convenient to use.The link is as follo...
wstt Microcontroller MCU
LTC3113 power supply problem help! !
I was adjusting the board these days. After soldering the LTC3113 power supply, the output voltage was not 3.3 but 0.6V. Has anyone encountered this situation? ? The feedback voltage was also 0.6V aft...
安静的白色风车 Power technology
Briefly talk about typedef struct
[i=s]This post was last edited by freebsder on 2018-12-4 00:45[/i] The problem comes from typedef struct Node { ElemType data; struct Node *next; }Node;. Changing it to typedef struct { ElemType data;...
freebsder MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2500  2765  480  74  2683  51  56  10  2  55 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号