EEWORLDEEWORLDEEWORLD

Part Number

Search

XCTN20144800B

Description
RES NET,THIN FILM,4.48K OHMS,100WV,.1% +/-TOL,-100,100PPM TC,0303 CASE
CategoryPassive components    The resistor   
File Size118KB,3 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

XCTN20144800B Overview

RES NET,THIN FILM,4.48K OHMS,100WV,.1% +/-TOL,-100,100PPM TC,0303 CASE

XCTN20144800B Parametric

Parameter NameAttribute value
Objectid1171462345
package instructionSMT, 0303
Reach Compliance Codeunknown
ECCN codeEAR99
structureChip
Manufacturer's serial numberCTN
Network TypeCenter Tap
Number of terminals6
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height0.254 mm
Package length0.762 mm
Package formSMT
Package width0.762 mm
method of packingTray
Rated power dissipation(P)0.25 W
GuidelineMIL-STD-883
resistance4480 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesCTN
size code0303
Temperature Coefficient100 ppm/°C
Tolerance0.1%
Operating Voltage100 V
CTN
Vishay Electro-Films
Nichrome Thin Film, Center Tapped Resistors
CHIP
RESISTORS
FEATURES
Wire bondable
Product may not
be to scale
Center tap feature
Chip size: 0.030 inches square
Resistance range total: 10
Ω
to 1 MΩ
Ratio tolerances to: 0.1 %
Resistor material: Nichrome
Oxidized silicon substrate for good power dissipation
The CTN series is a center tapped nichrome resistor chip
providing excellent stability at 250 mW power levels. The
CTN offers the designer flexibility in use as either a single
value resistor or as two resistors with a center tap feature.
The CTNs six bonding pads allows the user increased layout
flexibility.
The CTNs are manufactured using Vishay Electro-Films
(EFI) sophisticated thin film equipment and manufacturing
technology. The CTNs are 100 % electrically tested and
visually inspected to MIL-STD-883.
APPLICATIONS
The CTN center-tapped resistor chips are used mainly in feedback circuits of amplifiers where ratio matching, high power and
tracking between two resistors is critical.
Recommended for Hermetic environment where die is not exposed to moisture.
For low values, the resistance of the six bonding-pad configurations can vary, depending on the method of measurement used.
Vishay EFI measures low-value resistors by the four wire Kelvin technique.
TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES AND TOLERANCES
Tightest Standard Tolerance Available
0.5 %
0.1 %
± 10 ppm/°C
± 25 ppm/°C
± 50 ppm/°C
± 100 ppm/°C
PROCESS CODE
CLASS H*
203
202
200
201
*MIL-PRF-38534 inspection criteria
1 MΩ
CLASS K*
263
262
260
261
10
Ω
100
Ω
200
Ω
1 kΩ
STANDARD ELECTRICAL SPECIFICATIONS
PARAMETER
TCR Tracking Between Halves (R
A
/R
B
)
Center Tap Ratio,
R
A
/R
B
Tolerance
Noise, MIL-STD-202, Method 308, 100
Ω
- 250 kΩ
Stability, 1000 h, + 125 °C, 125 mW
Operating Temperature Range
Dielectric Voltage Breakdown
Insulation Resistance
Operating Voltage
DC Power Rating at + 70 °C (Derated to Zero at + 175 °C)
* 20 ppm/°C for
R
< 20
www.vishay.com
76
For technical questions, contact: efi@vishay.com
Document Number: 61024
Revision: 12-Mar-08
± 2 ppm/°C *
1 ± 1 % standard
- 35 dB typ.
± 0.1 %
ΔR/R
- 55 °C to + 125 °C
200 V
10
12
min.
100 V max.
250 mW
The program is burned into the microcontroller, but it must be connected to the burner all the time
I want to ask. Since the program has been burned, why can't the program be executed when I unplug the burner? My understanding is that after burning, the power supply should not be turned off, right?...
asyua TI Technology Forum
The importance of power supply in PCB circuit board design!
[align=left][color=rgb(62, 62, 62)]Power supply design is undoubtedly the most important part of the entire circuit board PCB design. If the power supply is unstable, nothing else can be discussed. I ...
ohahaha PCB Design
Equalized data signal! First-hand DDR5 simulation data (Part 2)
Author: Huang Gang, a member of Yibo Technology Expressway MediaYou have seen many balanced high-speed serial signals, but have you seen balanced DDR signals? Come, Mr. High Speed will show you!First,...
yvonneGan PCB Design
Why does an OS project compiled with WINCE6.0 R3 have such an error: CreateDirectory(C:) failed. GetLastError=5 (dec).
Why does an OS project compiled with WINCE6.0 R3 have such an error: CreateDirectory(C:) failed. GetLastError=5 (dec)....
ssssssss Embedded System
AD637 True RMS Conversion Chip
AD637 true RMS conversion chip---a good helper in power frequency measurement....
化升 TI Technology Forum
Regarding the packaging of the power interface (modified, please help me take a look)?
I drew a power interface package, model number is DC-005B, with three vias placed on each pad. Can you see if this is possible? If it is possible, I still have a question: because my three vias are co...
swfc_qinmm PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1249  2055  1867  2023  172  26  42  38  41  4 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号