EEWORLDEEWORLDEEWORLD

Part Number

Search

XCTN2023740AC

Description
RES NET,THIN FILM,374 OHMS,100WV,.2% +/-TOL,-25,25PPM TC,0303 CASE
CategoryPassive components    The resistor   
File Size118KB,3 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

XCTN2023740AC Overview

RES NET,THIN FILM,374 OHMS,100WV,.2% +/-TOL,-25,25PPM TC,0303 CASE

XCTN2023740AC Parametric

Parameter NameAttribute value
Objectid1171465050
package instructionSMT, 0303
Reach Compliance Codeunknown
ECCN codeEAR99
structureChip
Manufacturer's serial numberCTN
Network TypeCenter Tap
Number of terminals6
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height0.254 mm
Package length0.762 mm
Package formSMT
Package width0.762 mm
method of packingTray
Rated power dissipation(P)0.25 W
GuidelineMIL-STD-883
resistance374 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesCTN
size code0303
Temperature Coefficient-25,25 ppm/°C
Tolerance0.2%
Operating Voltage100 V
CTN
Vishay Electro-Films
Nichrome Thin Film, Center Tapped Resistors
CHIP
RESISTORS
FEATURES
Wire bondable
Product may not
be to scale
Center tap feature
Chip size: 0.030 inches square
Resistance range total: 10
Ω
to 1 MΩ
Ratio tolerances to: 0.1 %
Resistor material: Nichrome
Oxidized silicon substrate for good power dissipation
The CTN series is a center tapped nichrome resistor chip
providing excellent stability at 250 mW power levels. The
CTN offers the designer flexibility in use as either a single
value resistor or as two resistors with a center tap feature.
The CTNs six bonding pads allows the user increased layout
flexibility.
The CTNs are manufactured using Vishay Electro-Films
(EFI) sophisticated thin film equipment and manufacturing
technology. The CTNs are 100 % electrically tested and
visually inspected to MIL-STD-883.
APPLICATIONS
The CTN center-tapped resistor chips are used mainly in feedback circuits of amplifiers where ratio matching, high power and
tracking between two resistors is critical.
Recommended for Hermetic environment where die is not exposed to moisture.
For low values, the resistance of the six bonding-pad configurations can vary, depending on the method of measurement used.
Vishay EFI measures low-value resistors by the four wire Kelvin technique.
TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES AND TOLERANCES
Tightest Standard Tolerance Available
0.5 %
0.1 %
± 10 ppm/°C
± 25 ppm/°C
± 50 ppm/°C
± 100 ppm/°C
PROCESS CODE
CLASS H*
203
202
200
201
*MIL-PRF-38534 inspection criteria
1 MΩ
CLASS K*
263
262
260
261
10
Ω
100
Ω
200
Ω
1 kΩ
STANDARD ELECTRICAL SPECIFICATIONS
PARAMETER
TCR Tracking Between Halves (R
A
/R
B
)
Center Tap Ratio,
R
A
/R
B
Tolerance
Noise, MIL-STD-202, Method 308, 100
Ω
- 250 kΩ
Stability, 1000 h, + 125 °C, 125 mW
Operating Temperature Range
Dielectric Voltage Breakdown
Insulation Resistance
Operating Voltage
DC Power Rating at + 70 °C (Derated to Zero at + 175 °C)
* 20 ppm/°C for
R
< 20
www.vishay.com
76
For technical questions, contact: efi@vishay.com
Document Number: 61024
Revision: 12-Mar-08
± 2 ppm/°C *
1 ± 1 % standard
- 35 dB typ.
± 0.1 %
ΔR/R
- 55 °C to + 125 °C
200 V
10
12
min.
100 V max.
250 mW
Ask a Question
Why can't the file be downloaded?...
咻咻咻 Download Centre
I2C master-slave communication problem between 430 and 51
The voltage of 430 is 3.3V, and that of 51 is 5V. Now I use 430 as the host and operate 51. I find that the data read by I2C is incorrect. Is it because of the voltage drive problem? I can use 51 to c...
shuigui Microcontroller MCU
Share a FAT and FAT32 file system information
[i=s] This post was last edited by azhiking on 2014-2-13 14:03 [/i] I want to DIY an mp3, and I have collected some information about the file system, and will continue to share it...
azhiking Embedded System
TFT backlight voltage output problem
The voltage at LED1+ is 5V, and it cannot output a voltage of about 27V. Is it the two diodes that have problems? What is the most likely problem?...
gongjian32 Analogue and Mixed Signal
Signal processing after bridge differential connection
[i=s] This post was last edited by paulhyde on 2014-9-15 03:22 [/i] Hey guys, I'm a newbie here, I'd like to ask how to connect the output filter shaping amplifier circuit after the bridge differentia...
you_xiaohui Electronics Design Contest

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1022  292  847  97  649  21  6  18  2  14 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号