EEWORLDEEWORLDEEWORLD

Part Number

Search

8N3S272BC-1075CDI

Description
LVPECL Output Clock Oscillator
CategoryPassive components    oscillator   
File Size473KB,18 Pages
ManufacturerIDT (Integrated Device Technology)
Environmental Compliance  
Download Datasheet Parametric View All

8N3S272BC-1075CDI Overview

LVPECL Output Clock Oscillator

8N3S272BC-1075CDI Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Objectid1320160172
Reach Compliance Codecompliant
Other featuresENABLE/DISABLE FUNCTION; DIFFERENTIAL OUTPUT; TRAY
maximum descent time0.45 ns
Frequency Adjustment - MechanicalNO
frequency stability100%
JESD-609 codee3
Installation featuresSURFACE MOUNT
Nominal operating frequency150 MHz
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Oscillator typeLVPECL
Output load50 OHM
physical size7.0mm x 5.0mm x 1.55mm
longest rise time0.45 ns
Maximum supply voltage2.625 V
Minimum supply voltage2.375 V
Nominal supply voltage2.5 V
surface mountYES
maximum symmetry53/47 %
Terminal surfaceMatte Tin (Sn)
LVPECL Frequency-Programmable
Crystal Oscillator
IDT8N3S272
DATA SHEET
General Description
The IDT8N3S272 is a Frequency-Programmable Crystal Oscillator
with very flexible frequency programming capabilities. The device
uses IDT’s fourth generation FemtoClock® NG technology for an
optimum of high clock frequency and low phase noise performance.
The device accepts 2.5V or 3.3V supply and is packaged in a small,
lead-free (RoHS 6) 6-lead ceramic 5mm x 7mm x 1.55mm package.
The device can be factory programmed to any frequency in the range
from 15.476MHz to 866.67MHz and from 975MHz to 1,300MHz and
supports a very high degree of frequency precision of 218Hz or
better. The extended temperature range supports wireless
infrastructure, telecommun- ication and networking end equipment
requirements.
Features
Fourth generation FemtoClock® NG technology
Factory-programmable clock output frequency from 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz
Frequency programming resolution is 218Hz and better
One 2.5V or 3.3V LVPECL clock output
Output enable control (positive polarity), LVCMOS/LVTTL
compatible
RMS phase jitter @ 156.25MHz (12kHz - 20MHz): 0.24ps
(typical), integer PLL feedback configuration
RMS phase jitter @ 156.25MHz (1kHz - 40MHz): 0.27ps (typical),
integer PLL feedback configuration
2.5V or 3.3V supply
-40°C to 85°C ambient operating temperature
Available in a lead-free (RoHS 6) 6-pin ceramic package
Block Diagram
PFD
&
LPF
FemtoClock® NG
VCO
1950-2600MHz
Pin Assignment
DNU
1
2
3
6
5
4
V
CC
nQ
Q
nOE
V
EE
OSC
f
XTAL
2
÷P
÷N
Q
nQ
÷MINT,
MFRAC
25
Configuration Register (ROM)
nOE
Pulldown
7
IDT8N3S272
6-lead ceramic 5mm x 7mm x 1.55mm
package body
CD Package
Top View
IDT8N3S272CCD
REVISION A NOVEMBER 28, 2012
1
©2012 Integrated Device Technology, Inc.
pic18 starterkit learning 0x0E——EEPROM
[i=s]This post was last edited by mzb2012 on 2016-12-9 21:20[/i] [size=5]I. Introduction[/size] [size=3]EEPROM is an electrically erasable programmable read-only memory, which is a storage area that d...
mzb2012 Microchip MCU
Newbie questions about CPLD and DSP algorithms
I am a beginner and would like to ask a naive question: Can CPLD realize control algorithms alone? What is the difference between using CPLD and DSP to realize control algorithms?...
不锈钢老鼠 FPGA/CPLD
SUPERSYNC MD-10III、SUPERYNC PWB-1290、SUPERSYNC PWB1291、SUPER
Power supply circuit diagrams of six color monitors: SUPERSYNC MD-10III, SUPERYNC PWB-1290, SUPERSYNC PWB1291, SUPERSYNC PWB-1293, SUPERSYNC PWB-1361, SUPERSYNC PWB-1362...
破茧佼龙 Power technology
LCD screen driver board
I am making an interface board for an 8-inch LCD screen. The input data line is 24 bits, and VD[23:0] is in R:G:B 8:8:8 bit mode. The data line of the LCD screen is also 24 bits, but I want to use R:G...
iyj Embedded System
How to get the bitmap handle HBITMAP based on the image file stream
SHLoadImageFile can get the bitmap handle HBITMAP according to the file. Is there an API to get the bitmap handle according to the file stream? If not, how to implement it? Is there any related code?...
chenls Embedded System
TPS54340 has no output
[size=4][color=#000]Some time ago, I used [/color][color=rgb(205, 23, 31)]TPS54340[/color][color=#000] to make a circuit, 30V input, 20V2.5A output, the result is that it is normal for a while, and th...
Dong Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2925  1182  2348  1154  2861  59  24  48  58  19 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号