EEWORLDEEWORLDEEWORLD

Part Number

Search

8N4S272BC-0156CD

Description
LVDS Output Clock Oscillator
CategoryPassive components    oscillator   
File Size599KB,18 Pages
ManufacturerIDT (Integrated Device Technology)
Environmental Compliance
Download Datasheet Parametric View All

8N4S272BC-0156CD Overview

LVDS Output Clock Oscillator

8N4S272BC-0156CD Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid1308557800
Reach Compliance Codecompliant
Other featuresENABLE/DISABLE FUNCTION; DIFFERENTIAL OUTPUT; TRAY
maximum descent time0.45 ns
Frequency Adjustment - MechanicalNO
frequency stability100%
Installation featuresSURFACE MOUNT
Nominal operating frequency121.109 MHz
Maximum operating temperature70 °C
Minimum operating temperature
Oscillator typeLVDS
physical size7.0mm x 5.0mm x 1.55mm
longest rise time0.45 ns
Maximum supply voltage2.625 V
Minimum supply voltage2.375 V
Nominal supply voltage2.5 V
surface mountYES
maximum symmetry53/47 %
LVDS Frequency-Programmable
Crystal Oscillator
IDT8N4S272
DATA SHEET
General Description
The IDT8N4S272 is a Factory Frequency-Programmable Crystal
Oscillator with very flexible frequency programming capabilities. The
device uses IDT’s fourth generation FemtoClock
®
NG technology for
an optimum of high clock frequency and low phase noise
performance. The device accepts 2.5V or 3.3V supply and is
packaged in a small, lead-free (RoHS 6) 6-lead ceramic 5mm x 7mm
x 1.55mm package.
The device can be factory programmed to any in the range from
15.476MHz to 866.67MHz and from 975MHz to 1,300MHz and
supports a very high degree of frequency precision of 218Hz or
better. The extended temperature range supports wireless
infrastructure, telecommunication and networking end equipment
requirements.
Features
Fourth generation FemtoClock
®
NG technology
Factory-programmable clock output frequency from 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz
Frequency programming resolution is 218Hz and better
One 2.5V, 3.3V LVDS clock output
Output enable control (positive polarity), LVCMOS/LVTTL
compatible
RMS phase jitter @ 231.25MHz (12kHz - 20MHz):
0.48ps (typical), integer PLL feedback configuration
RMS phase jitter @ 231.25MHz (1kHz - 40MHz):
0.50ps (typical), integer PLL feedback configuration
2.5V or 3.3V supply
-40°C to 85°C ambient operating temperature
Available in a lead-free (RoHS 6) 6-pin ceramic package
Block Diagram
PFD
&
LPF
FemtoClock
®
NG
VCO
1950-2600MHz
Pin Assignment
DNU 1
6 V
DD
5 nQ
4 Q
OSC
f
XTAL
2
÷P
÷N
Q
nQ
nOE 2
GND 3
÷MINT,
MFRAC
25
Configuration Register (ROM)
nOE
Pulldown
7
IDT8N4S272
6-lead ceramic 5mm x 7mm x 1.55mm
package body
CD Package
Top View
IDT8N4S272CCD
REVISION A OCTOBER 3, 2012
1
©2012 Integrated Device Technology, Inc.
Solution to Invalid argument error when compiling SimplicityStudio V3
[i=s]This post was last edited by dcexpert on 2015-4-6 23:59[/i] When using SimplicityStudio V3 to compile 51 programs, when calling ohx51 to convert omf format, you may sometimes encounter the follow...
dcexpert 51mcu
Analog ICs
Definition: Analog integrated circuits mainly refer to integrated circuits that are composed of analog circuits such as capacitors, resistors, and transistors and are used to process analog signals. T...
jamieyang Power technology
WinCE memory problem
I just started to use WinCE, mainly developing under CEPC. I have two questions to ask: 1) After WinCE is loaded into the memory, what is the layout of the physical memory? 2) Does WinCE support virtu...
liren198 Embedded System
All roads lead to energy conservation. Where are the challenges and opportunities of energy conservation?
Moore's Law states that every 24 months (later revised to 18 months by the industry), the number of transistors that can be accommodated on an IC doubles, and performance will also double. After the d...
clj2004000 Power technology
When drawing a 4-layer board in Altium Designer 16, does the power ground in the middle layer need additional connection?
When drawing a 4-layer board, add an inner power layer, and after NET is selected as ground, do you need to do additional operations to connect this layer to the power ground?...
hust_wj PCB Design
The tx-1c MCU development board is still connected when using SIP burning. Please power on the MCU (I have tested it many times, please analyze it)
I am using [b]stc89c52[/b], a development board from the AOK MCU Learning and Development Network. When using STC-ISP to burn the program, it always prompts "Still connecting, please power on the MCU"...
hdrnono 51mcu

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 850  2762  1307  505  1862  18  56  27  11  38 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号