85/86 – 5/8 ˝ Square Single-Turn Panel Control with Rotary Switch
Potentiometer Specifications
Standard Resistance Range
Linear Tapers (A, B, E, & H)......................................................................... (B & E) 1 K ohms to 1 megohm ................. (A & H) 100 ohms to 1 megohm
Audio Tapers (C, D, F, G, S, & T) ................................................................ (D, G, S, & T) 1 K ohms to 1 megohm ....... (C & F) 1 K ohms to 1 megohm
Total Resistance Tolerance................................................................................. ±20 % or 10 %............................................ ±10 % or 5 %
Operating Temperature Range ........................................................................... -40 °C to +125 °C ....................................... -40 °C to +125 °C
Storage Temperature Range .............................................................................. -55 °C to +125 °C ....................................... -55 °C to +125 °C
Temperature Coefficient Over Storage Temperature Range .............................. ±1,000 ppm/°C ........................................... ±150 ppm/°C
Vibration (Single Section) ................................................................................... 15 G ........................................................... 15 G
Total Resistance Shift .................................................................................. ±2 % maximum .......................................... ±2 % maximum
Voltage Ratio Shift ....................................................................................... ±5 % maximum .......................................... ±5 % maximum
Shock (Single Section) ....................................................................................... 30 G ........................................................... 30 G
Total Resistance Shift .................................................................................. ±2 % maximum .......................................... ±2 % maximum
Voltage Ratio Shift ....................................................................................... ±5 % maximum .......................................... ±5 % maximum
Load Life ............................................................................................................. 1,000 hours ................................................ 1,000 hours
Total Resistance Shift .................................................................................. ±10 % maximum ........................................ ±5 % maximum
Rotational Life (No Load).................................................................................... 100,000 cycles ........................................... 100,000 cycles
Total Resistance Shift .................................................................................. (Linear taper) 10 ohms or .......................... (All tapers) ±5 % TRS maximum
Moisture Resistance (MIL-STD-202, Method 103, Condition B)
Total Resistance Shift .................................................................................. (B & E tapers) ±10 % maximum ................ ±5 % maximum (all tapers)
Starting and Running Torque (Non-Locking Bushings)
Single Section..................................................................................................................................................................................0.14 to 1.06 N-cm (0.2 to 1.5 oz.-in.)
Dual Section ....................................................................................................................................................................................0.14 to 1.06 N-cm (0.2 to 1.5 oz.-in.)
Triple Section ...................................................................................................................................................................................0.35 to 1.41 N-cm (0.5 to 2.0 oz.-in.)
Quadruple Section ...........................................................................................................................................................................0.35 to 1.41 N-cm (0.5 to 2.0 oz.-in.)
Starting and Running Torque (Locking Bushings) ....................................................................................................................0.14 to 2.82 N-cm (0.2 to 4.0 oz.-in.)
Shaft Locking Torque with Locknut @ 10 in-lb. (B & E Bushings) .......................................................................................................................14 N-cm (20 oz-in.)
Mounting ...................................................................................................................................................................................1.7-2.0 N-m (15-18 lb.-in.) maximum
Weight (Single Section) ............................................................................................................................................................................................. 21 grams maximum
(Each Additional Section)...................................................................................................................................................................................... 6 grams maximum
Terminals ...........................................................................................................................................................................................Printed circuit terminals or J-Hooks
Soldering Condition .................................................................................. Recommended hand soldering using Sn95/Ag5 no clean solder, 0.025 ˝ wire diameter.
Maximum temperature 399 °C (750 °F) for 3 seconds. No wash process to be used with no clean flux.
Marking ...........................................................................................Manufacturer’s trademark, wiring diagram, date code and resistance, manufacturer’s part number
Ganging (multiple section potentiometers) ...................................................................................................................................................................... 4 cup maximum
Hardware ...............One lockwasher and one mounting nut is shipped with each potentiometer; locking bushing versions are shipped with one additional locking nut
For dimensional drawings see pages 3 & 4. For ordering information see page 5.
NOTE: Model 81/82 performance specifications do not apply to units subjected to printed circuit board cleaning procedures.
1
Electrical specifications tested at 250 RPM, at room ambient: +25 °C nominal.
Initial Electrical Characteristics
1
Conductive Plastic Element
Cermet Element
Environmental Characteristics
1
Mechanical Characteristics
WARNING
Cancer and Reproductive Harm
www.P65Warnings.ca.gov
*RoHS Directive 2015/863, Mar 31, 2015 and Annex.
Specifications are subject to change without notice. Users should verify actual device performance in their specific
applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the
last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
81/82 – 5/8 ˝ Square Single-Turn Panel Control
85/86 – 5/8 ˝ Square Single-Turn Panel Control with Rotary Switch
Rotary Switch Specifications
Initial Electrical Characteristics
1
Contacts:
DPST ............................................................................................................................................................................. N.O/N.O.,N.C./N.C. or N.O./N.C.
Power Rating (Resistive Load):
DPST ..........................................................................................................2 A @ 125 volts RMS-60 Hz or 2 A @ 28 VDC, 1 A @ 250 volts RMS-60 Hz
Operating Temperature Range ...................................................................................................................................................................... -40 °C to +70 °C
Storage Temperature Range ....................................................................................................................................................................... -65 °C to +125 °C
Vibration (Dual Section)......................................................................................................................................................................................................8 G
(Triple Section) ..................................................................................................................................................................................................5 G
(Quadruple Section) ..........................................................................................................................................................................................3 G
Contact Resistance .......................................................................................................................................................................10 milliohms maximum
Contact Bounce ......................................................................................................................................................................... 0.1 millisecond maximum
Shock (Dual Section) ........................................................................................................................................................................................................20 G
(Triple Section) ....................................................................................................................................................................................................15 G
(Quadruple Section) ............................................................................................................................................................................................10 G
Contact Resistance .......................................................................................................................................................................10 milliohms maximum
Contact Bounce ......................................................................................................................................................................... 0.1 millisecond maximum
Switch Actuating Torque (50% Duty cycle @ Rated Power Load) .................................................................................1.41 to 4.94 N-cm (2 to 7 oz.-in.)
Contact Resistance .....................................................................................................................................................................100 milliohms maximum
Moisture Resistance (MIL-STD-202, Method 106, Condition B)
Contact Resistance (0.1 VDC-10 mA) ..........................................................................................................................................10 milliohms maximum
Switch Housing Material ................................................................................................................. High temperature, flame retardant, thermosetting plastic
Mechanical Characteristics
1
Actuating Torque (Each Section, Switch Module Only) ......................................................................................................3.53 to 10.6 N-cm (5 to 15 oz.-in.)
Running Torque (Out of Detent, 2-4 Module Assembly) ....................................................................................................0.21 to 1.41 N-cm (0.3 to 2 oz.-in.)
Detent ....................................................................................................................................................................................................CW or CCW standard
Contact Materials......................................................................................................................................................................... Fine silver with gold overlay
Terminal Styles .................................................................................................................................................................................................Solder lug only
Standard Orientation .............................................................................................................................................................In-line with control terminals
Optional .........................................................................................................................................................................Rotated 90 ° CCW from standard
Terminal Strength (Before and After Soldering Heat Exposure) ........................................................................................................ 0.9 Kg (2 lbs.) minimum
1
NOTE: Model 81/82 performance specifications do not apply to units subjected to printed circuit board cleaning procedures.
Electrical specifications tested at 250 RPM, at room ambient: +25 °C nominal.
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
Terminal outlines shown as solid lines represent PC Pins, available
on Model 81. Dashed line terminal outline represents "J" Hook,
available on Model 82.
5.97 ± .38
(.235 ± .015)
5.08 ± .38
(.200 ± .015)
12.7
(.50)
5.33 ± .76
(.210 ± .03)
10.16 ± .13
(.400 ± .005)
Note: For units with dual concentric shaft styles, a
2.54 (.100) spacer is added between the module(s) driven
by the outer shaft and those driven by the inner shaft.
For G, K, or V shafts, add the spacer between
modules 1 and 2. For L or M shafts, add the spacer
between modules 2 and 3. For N or P shafts, add the
spacer between modules 3 and 4.
SLOTTED SHAFT
*EXCLUDES MODELS 83 AND 84
DIMENSIONS:
MM
(INCHES)
Suggested Panel Layout
B
C
BUSHING
A, B & J
E
DIM A
9.91
(.39)
ANTI-ROTATION LUG
A
B
C
E
F
J
K
DIM B
7.75
(.305)
7.75
(.305)
N/A
13.49
(.531)
N/A
9.53
(.375)
9.53
(.375)
DIM C
N/A
7.75
(.305)
7.75
(.305)
N/A
N/A
N/A
9.53
(.375)
DIM D
N/A
N/A
N/A
N/A
7.75
(.305)
N/A
N/A
DIM E
2.49
(.098)
2.49
(.098)
2.49
(.098)
3.45
(.136)
2.54
(.100)
2.54
(.100)
2.54
(.100)
D
A
C, E & N
R&S
U
6.73
(.265)
10.5
(.413)
7.5
(.295)
DIMENSIONS:
MM
(INCHES)
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
85/86 – 5/8 ˝ Square Single-Turn Panel Control with Rotary Switch
Product Dimensions
Primary Potentiometer Module
Model 85/86
14.53
(.572)
9.58 ± .38
(.377 ± .015)
Secondary Potentiometer Module
Model 85/86
10.16
(.400)
15.88
(.625)
15.88
(.625)
Shaft Flat Orientation*
120 ° ± 5 ° CCW END
30 ° ± 5 °
12.7
(.50)
5.97
(.235)
8.56
(.337)
1.60
(.063)
FLATTED SHAFT
5.08
(.200)
SLOTTED SHAFT
*EXCLUDES MODELS 83 AND 84
5.08
(.200) 8.56
(.337)
5.08
(.200)
Switch Module
Model 85/86
REAR
PLATE
COVER
2.77
(.109)
1.35
(.053)
2.29
(.090)
TYP.
6 PLACES
Assembly Sequence
Model 85/86
Secondary Potentiometer Module
Switch Module Terminal Orientation
3
1
4
2
3
1
18.42
(.725)
2.41
1.14
(.095)L X (.045)W
SLOT TYP. 6 PLACES
4
2
HORIZONTAL ORIENTATION
(Types R56, R57, R58 & R59)
VERTICAL ORIENTATION
(Types R50, R51, R52 & R53)
2.92
(.115)
9.53
(.375)
REAR
COVER
PLATE
SWITCH
MODULE
PRIMARY
POTENTIOMETER
MODULE
4
2
3
1
3
1
4
2
DPST (NO/NC)
(TYPES 50, 51, 56, 57)
DPST (NO/NO)
(TYPES 52, 53, 58, 59)
Switch contacts shown in detent position.
Locating Lug Options - All Model 80 Series
A
.46
(.018)
7.75
(.305)
E
13.49
(.531)
J
9.53
(.375)
.79 ± .41
(.031 ± .016)
E = 2.36 ± .76
(.093 ± .03)
H & J = 1.98 ± .41
(.078 ± .016)
2.31
(.091)
3.18
(.125)
.46
(.018)
2.36
(.093)
7.75
(.305)
A
C
7.75
(.305)
.46
(.018)
.79 ± .41
(.031 ± .016)
MOUNTING
SURFACE
TOLERANCES EXCEPT AS SHOWN: DECIMAL .XXX ±
RECOMMENDED
PANEL LAYOUT
7.75
#40 DRILL
(.305)
2.49
DIA.
(.098)
9.91
DIA.
(.390)
.127
(.005)
.XX ± .38
(.015)
ANGLE ± 5 %
2.31
(.091)
DIMENSIONS:
MM
(INCHES)
NOTE: "D" OPTION - NO A/R LUG. OTHER LOCATING LUG OPTIONS AVAILABLE. CONSULT FACTORY FOR DETAILS.
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
I am not very clear about the working principle of input capture of stm32. Take time2 as an example. Are ch1 and ch2 in the same group, one for measuring the number of cycles and the other for measuri...
Does the 5.0 BSP need to burn the tocblock1 file? Where is this file? I didn't find this file in the 5.0 BSP, but there is this file in 4.2. Can I directly download this file? Thank you....
[size=5][color=#8b0000]Model: IMX6-CB200[/color][/size] [color=#ff0000]Question: [/color] [color=#ff0000]Pins 11, 150, and 152 are configured as normal gpio. When tsc2007 is hung under iic1, it is con...
[i=s]This post was last edited by Qiangzi00001 on 2015-9-25 16:41[/i] [align=left][font=宋体] I finally came back after a week of playing[/font]:lol:lol[font=宋体], and I happened to have a[/font]MPU9250[...
PV DC fuses are safety devices used to protect PV panels, inverters, and DC loads. To ensure their safety and reliability, they must be UL248 certified.
Before applying for UL248 certifi...[Details]
Electric vehicles are currently gaining momentum, but this is just a facade. Fuel-powered vehicles remain unchallenged. While electric vehicles boast unique advantages in environmental emissions an...[Details]
With the rapid development of technology, automotive intelligence is increasing at an unprecedented rate. This not only enhances vehicle functionality and comfort, but also places higher deman...[Details]
New energy pure electric vehicles generally accelerate faster than comparable fuel-powered vehicles, both from a standing start and while accelerating. Many believe this is simply due to the motor'...[Details]
Amidst the wave of intelligent automotive transformation, advanced driver assistance is gradually emerging from cutting-edge technology into the mainstream, becoming a new frontier of industry comp...[Details]
With the rapid advancement of automation technology, collaboration between robots is no longer just science fiction. Imagine dozens of machines moving goods in a warehouse without interfering with ...[Details]
Charging is a familiar process for new energy vehicles, and as a source of battery energy, charging piles are crucial. New energy vehicle charging can be divided into fast charging and slow chargin...[Details]
In daily life, power transformers have different functions and uses due to different usage scenarios. The most common ones can be divided into: control transformers, isolation transformers, rectifi...[Details]
During daily operation of an R-type power transformer, the voltage used varies as the equipment being used adjusts. This raises the question: can the transformer change voltage at this point? The a...[Details]
Compiled from semiengineering
The industry is increasingly concerned about power consumption in AI, but there are no simple solutions. This requires a deep understanding of software and ...[Details]
In this final installment of a five-part blog series, I will discuss noise in op amps driving headphone loads and some techniques for reducing it. Previous posts have discussed headphone load power...[Details]
Renesas Electronics introduces a new USB-C power solution with an innovative three-level topology.
Improve performance while reducing system size
New solution combines excel...[Details]
The intelligent
dust monitoring system intelligently monitors dust concentrations at and around construction sites. All concentration values are transmitted to a cloud server for
cloud co...[Details]
The primary control objective in this case is the display and alarming of data parameters on the Xinheng control scale instrument. The system's main PLC uses a Siemens CPU, and data is collected vi...[Details]
Servo motors, also known as actuator motors, serve as actuators in automatic control systems, converting received electrical signals into angular displacement or angular velocity output on the moto...[Details]
stm32/stm8
京公网安备 11010802033920号
EEWORLD
