INCH-POUND
MS24266R
1 December 2016
SUPERSEDING
MS24266P
7 August 2015
DETAIL SPECIFICATION SHEET
CONNECTORS, PLUG, ELECTRICAL, STRAIGHT,
MINIATURE, CLASSES E, F, G AND R
Inactive for new design after 14 November 1977.
For new design, use MIL-DTL-83723, series III.
This specification is approved for use by all Departments
and Agencies of the Department of Defense.
The requirements for acquiring the product described herein
shall consist of this specification sheet and MIL-DTL-26500.
STYLE P (PIN INSERT) FOR CLASSES F, G, R AND E
FIGURE 1. Plug, threaded coupling, type T.
AMSC N/A
FSC 5935
MS24266R
STYLE S (SOCKET INSERT), CLASSES F, G, R AND E
FIGURE 1. Plug, threaded coupling, type T – Continued.
2
MS24266R
Inches
.005
.010
.015
.018
.019
.020
.022
.024
mm
0.13
0.25
0.38
0.46
0.48
0.51
0.56
0.61
Inches
.045
.048
.050
.054
.068
.071
.091
.125
mm
1.14
1.22
1.27
1.37
1.73
1.80
2.31
3.18
Inches
.140
.180
.194
.225
.260
.306
.325
.335
mm
3.56
4.57
4.93
5.72
6.60
7.77
8.26
8.51
Inches
.367
.403
.417
.450
.505
.515
1.375
mm
9.32
10.24
10.59
11.43
12.83
13.08
34.92
FIGURE 1. Plug, threaded coupling, type T – Continued.
3
MS24266R
OPTIONAL SHELL DESIGN,
CLASSES F, G & R
SHELL DESIGN
CLASS E ONLY
Inches
.015
.025
.073
.085
mm
0.38
0.66
1.85
2.16
Inches
.161
.220
.314
mm
4.09
5.59
7.98
Inches
.367
1.125
1.375
mm
9.32
28.58
34.92
NOTES:
1. Dimensions are in inches. Unless otherwise specified, tolerance on decimals is
±
.005.
2. Metric equivalents are given for information only.
3. All diameters to be concentric with each other within .015 TIR.
4. All diameters in the same plane to be concentric with each other within .004 TIR.
5. Distance between end of shell and the point at which a gauge pin having the same basic
diameter as the mating contact and a square face, engages socket contact spring.
6. Dimensions on pin and socket contact locations and end of shell to insert faces apply when
contacts are placed in inserts for inspection or application.
FIGURE 1. Plug, threaded coupling, type T – Continued.
4
MS24266R
7. Dimensions .071 may reduce to .056 minimum under pressures caused by molded cable
assemblies or sharp cable bends.
8. Use tool MIL-I-81969/17 to assemble contacts into this connector, and use tool MIL-I-81969/19 to
remove contacts from this connector.
9. Thread relief groove is optional on shell. When groove is omitted the length of full thread from
front of shell will be .221 minimum.
10. Environment resistant (classes F and R) plugs, type T aluminum shell material. Grounding
environment resistant (class G) plugs, type T aluminum shell material. Environment resistant
(class E) plugs, type T stainless steel shell material.
11. True position (TP) tolerances specified are for maximum material conditions (MMC).
12. Application note: For new design, use MIL-DTL-83723. Note: MIL-DTL-83723, series III,
specifies accessory threads and accessories that are not fully compatible with MIL-DTL-26500
connectors. Recommend using MIL-DTL-26500 cable clamps with these connectors.
FIGURE 1. Plug, threaded coupling, type T – Continued.
5
京公网安备 11010802033920号
EEWORLD
