SF81
8.0 AMP SUPER FAST RECTIFIERS
THRU
SF87
VOLTAGE RANGE
50 to 600 Volts
CURRENT
FEATURES
* Low forward voltage drop
* High current capability
* High reliability
* High surge current capability
* Good for switching mode application
.412
(10.5)
MAX.
.108
(2.75)
8.0 Amperes
3.8
f
+.2
HOLE THRU
TO-220A
.180
(4.6)
.050
(1.27)
.248
(6.3)
MECHANICAL DATA
* Case: Molded plastic
* Epoxy: UL 94V-0 rate flame retardant
* Lead: Lead solderable per MIL-STD-202,
method 208 guranteed
* Polarity: As Marked
* Mounting position: Any
* Weight: 2.24 grams
.040
(1.0)
MAX.
.051 MAX.
(1.3)
.040 MAX.
(1.0)
.200
(5.08)
+
CASE
.595
(15.1)
MAX.
.550
(14.0)
.158
(4.0) MIN.
MAX.
.120
(3.05)
PIN 1
+
CASE
PIN 2
Case Negative
Suffix "R"
PIN 1
PIN 2
+
Case Positive
Dimensions in inches and (millimeters)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating 25 C ambient temperature uniess otherwies specified.
Single phase half wave, 60Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
TYPE NUMBER
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Voltage
Maximum DC Blocking Voltage
Maximum Average Forward Rectified Current
.375"(9.5mm) Lead Length at Tc=100 C
Peak Forward Surge Current, 8.3 ms single half sine-wave
superimposed on rated load (JEDEC method)
Maximum Instantaneous Forward Voltage at 8.0A
Maximum DC Reverse Current
Tc=25 C
at Rated DC Blocking Voltage
Tc=100 C
Maximum Reverse Recovery Time (Note 1)
Typical Junction Capacitance (Note 2)
Operating and Storage Temperature Range T
J
, T
STG
NOTES:
SF81
50
35
50
SF82
100
70
100
SF83
150
105
150
SF84
200
140
200
8.0
125
SF85
300
210
300
SF86
400
280
400
SF87 UNITS
600
420
600
V
V
V
A
A
V
mA
mA
nS
pF
C
0.95
10
500
35
50
-65 +150
1.30
1.50
50
1. Reverse Recovery Time test condition: IF=0.5A, IR=1.0A, IRR=0.25A
2. Measured at 1MHz and applied reverse voltage of 4.0V D.C.
RATING AND CHARACTERISTIC CURVES (SF81 THRU SF87)
FIG.1- TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC
50
W
NONINDUCTIVE
10
W
NONINDUCTIVE
trr
+0.5A
|
|
|
|
|
|
|
|
FIG.2-TYPICAL FORWARD CURRENT
DERATING CURVE
AVERAGE FORWARD CURRENT,(A)
12
10
8
6
4
2
0
Single Phase
Half Wave 60Hz
Resistive Or Inductive Load
(+)
25Vdc
(approx.)
( )
1
W
NON-
INDUCTIVE
OSCILLISCOPE
(NOTE 1)
D.U.T.
( )
PULSE
GENERATOR
(NOTE 2)
(+)
0
-0.25A
NOTES: 1. Rise Time= 7ns max., Input Impedance= 1 megohm.22pF.
2. Rise Time= 10ns max., Source Impedance= 50 ohms.
-1.0A
1cm
SET TIME BASE FOR
50 / 10ns / cm
0
25
50
75
100
125
150
175
CASE TEMPERATURE,( C)
FIG.3-TYPICAL FORWARD
CHARACTERISTICS
1000
50
INSTANTANEOUS FORWARD CURRENT,(A)
FIG.4-TYPICAL REVERSE
CHARACTERISTICS
REVERSE LEAKAGE CURRENT, (mA)
10
3.0
SF
81~
SF
84
SF
85
~S
F8
6
SF
87
100
Tc=100 C
1.0
10
Tj=25 C
Pulse Width 300us
1% Duty Cycle
Tc=25 C
0.1
1.0
.01
.4
.6
.8
1.0
1.2
1.4 1.6
1.8
0.1
0
20
40
60
80
100 120 140
FORWARD VOLT
AGE,(V)
PERCENT OF RATED PEAK REVERSE VOLT
AGE,(%)
FIG.5-MAXIMUM NON-REPETITIVE FORWARD
SURGE CURRENT
PEAK FORWARD SURGE CURRENT,(A)
125
FIG.6-TYPICAL JUNCTION CAPACITANCE
175
150
125
100
75
50
25
0
100
75
Tj=25 C
8.3ms Single Half
Sine Wave
JEDEC method
50
25
0
1
5
10
50
100
JUNCTION CAPACITANCE,(pF)
.01
.05
.1
.5
1
5
10
50
100
NUMBER OF CYCLES AT 60Hz
REVERSE VOLTAGE,(V)
PCB Design
京公网安备 11010802033920号
EEWORLD
