EEWORLDEEWORLDEEWORLD

Part Number

Search

3GV62A-30N-155.25

Description
LVCMOS Output Clock Oscillator, 155.25MHz Nom, SMD, 6 PIN
CategoryPassive components    oscillator   
File Size134KB,1 Pages
ManufacturerEuroquartz
Websitehttp://www.euroquartz.co.uk/
Environmental Compliance
Download Datasheet Parametric View All

3GV62A-30N-155.25 Overview

LVCMOS Output Clock Oscillator, 155.25MHz Nom, SMD, 6 PIN

3GV62A-30N-155.25 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid1292649794
package instructionSMD, 6 PIN
Reach Compliance Codecompliant
Other featuresTRI-STATE; ENABLE/DISABLE FUNCTION
Frequency Adjustment - MechanicalNO
Frequency offset/pull rate30 ppm
frequency stability25%
linearity10%
Installation featuresSURFACE MOUNT
Nominal operating frequency155.25 MHz
Maximum operating temperature70 °C
Minimum operating temperature
Oscillator typeLVCMOS
Output load15 pF
physical size11.4mm x 9.6mm x 2.5mm
Maximum supply voltage3.465 V
Minimum supply voltage3.135 V
Nominal supply voltage3.3 V
surface mountYES
maximum symmetry55/45 %
EURO
QUARTZ
LVCMOS SMD 11.4 x 9.6 x 2.5mm, 6 pad
Frequency range 50.01MHz to 200MHz
LVCMOS Output
Supply Voltage 3.3 VDC
High Q fundamental mode crystal
Low jitter multiplier circuit
Low unit cost
OUTLINE & DIMENSIONS
DESCRIPTION
GV62 VCXOs, are packaged in an industry-standard, 4 pad, 11.4mm
x 9.6mm x 2.5mm SMD package. The VCXO incorporates a high Q
fundamental mode crystal and a low jitter multiplier circuit.
SPECIFICATION
Frequency Range:
Supply Voltage:
Output Logic:
Integrated Phase Jitter:
Period Jitter RMS:
Period Jitter Peak to peak:
Phase Noise:
Initial Frequency Accuracy:
Output Voltage HIGH (1):
Output Voltage LOW (0):
Pulling Range:
Temperature Stability:
Output Load:
Start-up Time:
Duty Cycle:
Rise/Fall Times:
Current Consumption:
Linearity:
Modulation Bandwidth:
Input Impedance:
Slope Polarity:
(Transfer function)
GV62 VCXO
50.01MHz ~ 200.0MHz
50.01MHz to 200.0MHz
3.3 VDC ±5%
LVCMOS
2.3ps typical, 4.0ps maximum
(for 155.250MHz)
4.0ps typical (for 155.250MHz)
27.0ps typical (for 155.250MHz)
Tune to the nominal frequency
with Vc= 1.65 ±0.2VDC
90% Vdd minimum
10% Vdd maximum
From ±30ppm to ±150ppm
15pF
10ms maximum, 5ms typical
50% ±5% measured at 50% Vdd
1.2ns typical (15pF load)
25mA maximum (15pF load)
10% maximum, 6% typical
25kHz minimum
2 MW minimum
Monotonic and Positive. (
Storage Temperature:
Ageing:
Enable/Disable (Tristate):
RoHS Status:
-50° to +100°C
±5ppm per year maximum
Not available (
Fully compliant
PHASE NOISE
)
Offset
10Hz
100Hz
1kHz
10kHz
100kHz
1MHz
10MHz
Frequency 155.25MHz
-65dBc/Hz
-95dBc/Hz
-120dBc/Hz
-128dBc/Hz
-122dBc/Hz
-120dBc/Hz
-140dBc/Hz
FREQUENCY STABILITY
Stability Code Stability ±ppm Temp. Range
A
25
0°~+70°C
B
50
0°~+70°C
C
100
0°~+70°C
D
25
-40°~+85°C
E
50
-40°~+85°C
F
100
-40°~+85°C
If non-standard frequency stability is required
Use ‘I’ followed by stability, i.e. I20 for ±20ppm
PART NUMBER SCHEDULE
Example:
3GV62B-80N-155.25
Supply Voltage
3 = +3.3V
Series Designator
GV62
Stability over temperature range
(S
)
Pullability in ±ppm
Pullability determinator
N = minimum
M = maximum
T = Typical
Frequency in MHz
EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE
Tel: +44 (0)1460 230000 Fax: +44 (0)1460 230001 info@euroquartz.co.uk www.euroquartz.co.uk
RC passive filter circuit and its principle
[b] In the test system, RC filter is often used. Because in this field, the signal frequency is relatively low. The RC filter circuit is simple, has strong anti-interference, has good low-frequency pe...
qwqwqw2088 Analogue and Mixed Signal
ADS8332 Question 2: Where does this interference come from?
I used C2000's SPI to drive ADS8332. I've had success in the past, but it was on a different PCB. However, when I tried it again, I ran into a lot of problems. [/font] Phenomenon: When the sampling an...
dontium Analogue and Mixed Signal
I would like to ask about the timer interrupt problem (I have been unable to find any information, please give me some advice)
Question 1: Is it necessary to install the initial value of the timer in the main function? I seem to have tried it and it works fine without it. Question 2: If timer 0 is turned off in timer 1, do I ...
唐菲远 51mcu
How to implement the 20-bit address pointer of MSP430FG461X series in C language?
When I assign a 20-bit address 0x10000 to a pointer variable, it always says that it is out of the range of 0 to 0xFFFF.This is possible in assembly language, because MSP430X provides instructions wit...
我爱电子 Microcontroller MCU
Crystal oscillator problem
Please help me analyze this:the crystal oscillator is not working properly. It does not oscillate at first. Then I touch it with a soldering iron and it works normally for a while. Then it does not os...
chenzep Microcontroller MCU
Regarding the issue of running programs under pure DOS on the PC104 device, is there any difference between the pure DOS booted by the virtual floppy drive and the actually installed DOS?
As the title says. Now the program runs in pure DOS booted by virtual floppy drive. The program written in 2000 with bc31 runs smoothly in 2000, but it is very stuck in DOS. I want to compile it in DO...
lionedwolf Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2246  994  2263  2612  1850  46  21  53  38  14 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号