EEWORLDEEWORLDEEWORLD

Part Number

Search

3GW8C-80T-200.10

Description
LVCMOS Output Clock Oscillator, 200.1MHz Nom, ROHS AND REACH COMPLIANT, DIP-8/4
CategoryPassive components    oscillator   
File Size126KB,1 Pages
ManufacturerEuroquartz
Websitehttp://www.euroquartz.co.uk/
Environmental Compliance  
Download Datasheet Parametric View All

3GW8C-80T-200.10 Overview

LVCMOS Output Clock Oscillator, 200.1MHz Nom, ROHS AND REACH COMPLIANT, DIP-8/4

3GW8C-80T-200.10 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Objectid1063499799
package instructionROHS AND REACH COMPLIANT, DIP-8/4
Reach Compliance Codecompliant
Maximum control voltage1.85 V
Minimum control voltage1.45 V
Frequency Adjustment - MechanicalNO
Frequency offset/pull rate80 ppm
frequency stability100%
linearity10%
Installation featuresTHROUGH HOLE MOUNT
Nominal operating frequency200.1 MHz
Maximum operating temperature70 °C
Minimum operating temperature
Oscillator typeLVCMOS
Output load15 pF
physical size12.8mm x 12.8mm x 5.08mm
Maximum supply voltage3.465 V
Minimum supply voltage3.135 V
Nominal supply voltage3.3 V
surface mountNO
maximum symmetry55/45 %
EURO
QUARTZ
8 pin Dual-in-Line
Frequency range 200.1MHz to 800MHz
LVCMOS Output
Supply Voltage 3.3 VDC
High Q fundamental mode crystal
Low jitter multiplier circuit
DESCRIPTION
OUTLINE & DIMENSIONS
GW42 VCXOs, are packaged in an industry-standard, 4 pad, 11.4mm
x 9.6mm x 2.5mm SMD package. GW42 VCXOs incorporate a high Q
fundamental crystal and a low jitter multiplier circuit.
SPECIFICATION
Frequency Range:
Supply Voltage:
Output Logic:
Integrated Phase Jitter:
Period Jitter RMS:
Period Jitter Peak to peak:
Phase Noise:
Initial Frequency Accuracy:
Output Voltage HIGH (1):
Output Voltage LOW (0):
Pulling Range:
Temperature Stability:
Output Load:
Start-up Time:
Duty Cycle:
Rise/Fall Times:
Current Consumption
<96MHz:
>96MHz:
Linearity:
Modulation Bandwidth:
Input Impedance:
Slope Polarity:
(Transfer function)
GW8 VCXO
200.1MHz ~ 800.0MHz
200.1MHz to 800.0MHz
3.3 VDC ±5%
LVCMOS
2.6ps typical, 4.0ps maximum
(for 155.250MHz)
4.3ps typical (for 155.250MHz)
27.0ps typical (for 155.250MHz)
Tune to the nominal frequency
with Vc= 1.65 ±0.2VDC
90% Vdd minimum
10% Vdd maximum
From ±30ppm to ±150ppm
15pF
10ms maximum, 5ms typical
50% ±5% measured at 50% Vdd
1.2ns typical (15pF load)
30mA maximum (15pF load)
40mA maximum (15pF load)
10% maximum, 6% typical
25kHz minimum
2 MW minimum
Monotonic and Positive. (
PHASE NOISE
10Hz
100Hz
1kHz
10kHz
100kHz
1MHz
10MHz
-65dBc/Hz
-95dBc/Hz
-120dBc/Hz
-125dBc/Hz
-121dBc/Hz
-120dBc/Hz
-140dBc/Hz
Storage Temperature:
Ageing:
Enable/Disable (Tristate):
RoHS Status:
-50° to +100°C
±5ppm per year maximum
Not available (
Fully compliant
)
PART NUMBER SCHEDULE
Example:
FREQUENCY STABILITY
Stability Code Stability ±ppm Temp. Range
A
25
0°~+70°C
B
50
0°~+70°C
C
100
0°~+70°C
D
25
-40°~+85°C
E
50
-40°~+85°C
F
100
-40°~+85°C
If non-standard frequency stability is required
Use ‘I’ followed by stability, i.e. I20 for ±20ppm
3GW8B-80N-250.00
Supply Voltage
3 = +3.3V
Series Designator
GW8
Stability over temperature range
(
)
Pullability in ±ppm
Pullability determinator
N = minimum
M = maximum
T = Typical
Frequency in MHz
EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE
Tel: +44 (0)1460 230000 Fax: +44 (0)1460 230001 info@euroquartz.co.uk www.euroquartz.co.uk
Memories of Moscow
[i=s]This post was last edited by ienglgge on 2015-3-26 20:58[/i] A few days ago, I went to Russia on a business trip. It was my first time going abroad. Here, I will leave a few traces. I left in the...
ienglgge Talking
Handbook of commonly used electronic components pdg
A practical identification and detection manual for commonly used electronic components, for reference only! !...
wanghaixing Analog electronics
Has anyone used the software simulation I2C program provided by M4?
Has anyone used the software provided by M4 to simulate I2C? Did it work? My clock line and data line waveforms are exactly the same, what's the situation? ?...
1301120345 Microcontroller MCU
Is there anyone who has used ads1216? I have a question about the DSYNC synchronization function and I would like to ask for your advice!!!
I'm using ads1216 to collect multi-channel data recently, and I use cd4067 analog switch to switch the signal source. It takes time to switch the analog switch, so I use the synchronous DSYNC function...
xiaoaf Integrated technical exchanges
Where can I find the BSDL file for building a JTAG chain for msp430?
[color=#555555]Where can I find the BSDL file to build a JTAG chain? [/color] [color=#555555] All MSP430s have a JTAG interface that is only used for program development and flash programming. But thi...
Aguilera Microcontroller MCU
[Data Sharing] CORTEX-M0 Technical Reference Manual
Cortex-M0 Technical Reference Manual...
lixiaohai8211 NXP MCU

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 993  2086  2001  804  2864  20  42  41  17  58 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号