Above ratings are based on the thermal resistances using a multi-layer circuit board (EIA/JESD51). For mounting on a mono-layer board, power derating shall be
needed. Please inquire of us about conditions.
※1 素子毎の負荷電力の合計が、パッケージ定格電力を超えない条件で御½用ください。
※1 Total power consumption of all elements should not exceed the package power rating.
The resistor of this product is formed by narrow patterning a thin metal film. Thus, application of excessive voltage causes burn and destruction of the resistive film, abnormality
in resistance or open resistance and loss of proper function. The properly and electrostatically measured taping materials are used for the components, but attention should be paid
to the fact that there is some danger the parts may be destructed by static electricity(equivalent to 500V or over at 100pF, 1.5kΩ) to cause a change in resistance in the conditions
of an excessive dryness when mounting on the boards. Similarly, care should be given not to apply the excessive static electricity at the time of mounting on the boards. When
designing, consideration can be taken into withstanding ESD for customized KPC products. Please consult with us about the details.
●
Hand soldering by iron soldering or repairment are not recommended because KPC is a multi-pin product.
●
Avoid storing components under direct sun rays, high temperature/humidity. Direct sun rays will cause quality change of taping and difficulty of keeping appropriate peeling
strength. In the case of 5〜35℃/35〜75%RH, there is no deterioration of solderability for 12 months, but take special care for storing, because condensation, dust, and toxic gas
like hydrogen sulfide, sulfurous acid gas, hydrogen chloride, etc. may drop solderability.
The SPI of PXA310 is used to control MCP2515, and the transmission is normal. After writing the command word to 2515, the chip status register is read. The MISO pin signal is normal when observed by o...
[i=s]This post was last edited by jameswangsynnex on 2015-3-3 19:57[/i]3D is really hot. Japanese companies are taking the lead, and Chinese and Korean companies are also following up quickly. From th...
I got a TI 3503 EVM board and took a quick look at the datasheet. Questions: 1. Doesn't 3503 include a DSP core? But it is usually used in mobile phones for audio and video processing. Does the DSP bu...
Suppose I have a program like this [code] void test() { char temp=0; while(1) { temp=getchar(); /*It seems to stop here and wait for the return key*/ if(temp!= 0) { return ; } printf("loop....."); } }...
1 Introduction
The multifunctional monitor is a commonly used clinical medical device. It can display the patient's electrocardiogram (ECG), respiration (RESP), blood oxygen saturation (SP...[Details]
The circuit shown in the figure is a three-digit tachometer used to measure low frequency signals with a repetitive time interval of 0.235 to 15 seconds. The tachometer has a speed range of 4 to 255 r...[Details]
With the continuous improvement of living standards and the increase in the proportion of urban aging, the household use of medical electronic equipment has gradually become a trend. Among them, the...[Details]
At present, a hot spot for the research and development of hearing aids abroad is concentrated in China. To be more precise, it is based on the research of Chinese language and speech, and the deve...[Details]
Introduction: Design of automated test systems
Challenges
To ensure the quality and reliability of products delivered to customers, test managers and engineers use automated test system...[Details]
In the development of high-stability lasers, real-time monitoring of the working state of the laser is an issue that needs to be focused on. This system realizes the high-stability laser temperatur...[Details]
0 Introduction to the direct method of feedback linearization based on dynamic equilibrium state theory
The basic idea of the direct method of feedback linearization based on dynamic equilib...[Details]
Signal sources have developed to a very wide range today. We can classify them according to the frequency range: ultra-low frequency (0.1m～1kHz), audio (20Hz～20kHz), video (20kHz～10MHz), radio fre...[Details]
Adding "intelligence" to measurement systems is becoming more common as 8-bit microcontrollers are inexpensive, widely available, and can be programmed using today's common high-level languages, su...[Details]
Compared with traditional light sources, light-emitting diodes (LEDs) have many advantages, such as low operating voltage, high energy efficiency, small size and directional light. They can provide...[Details]
introduction
With the rapid development of my country's aviation industry, various new aircraft and control equipment have been successfully developed. Some previous measurement and control eq...[Details]
Lithium-ion batteries have a high energy-to-weight and energy-to-volume ratio, no memory effect, can be recharged many times, have a long service life, and are becoming increasingly cheaper. A good...[Details]
This article first briefly introduces the working principles of current mode and voltage mode and their respective advantages and disadvantages; then discusses the ideal voltage mode using output c...[Details]
Today's mobile phone production testing faces an increasingly complex environment, with challenges of multiple frequency bands and multiple standards, pressure on production test speed, and pres...[Details]
1. Introduction
The intelligent detector discussed in this paper is an integrated semiconductor photodetector. Compared with traditional semiconductor photosensitive devices, its most ...[Details]
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
