177-710-5-51P6K7-18RTG datasheet, PDF

Datasheet> All Categories > The connector> The connector> 177-710-5-51P6K7-18RTG

177-710-5-51P6K7-18RTG: DescriptionD Microminiature Connector, 51 Contact(s), Male, Plug,; CategoryThe connector The connector; File Size858KB，5 Pages; ManufacturerGlenair; Websitehttp://www.glenair.com/

Download Datasheet Parametric View All

177-710-5-51P6K7-18RTG Overview

D Microminiature Connector, 51 Contact(s), Male, Plug,

177-710-5-51P6K7-18RTG Parametric

Parameter Name	Attribute value
Objectid	7004455432
Reach Compliance Code	unknown
ECCN code	EAR99
Other features	STANDARD: MIL-DTL-83513
Body/casing type	PLUG
Connector type	D MICROMINIATURE CONNECTOR
Contact point gender	MALE
DIN compliance	NO
empty shell	NO
Filter function	NO
IEC compliance	NO
insulator material	LIQUID CRYSTAL POLYMER/POLYPHENYLENE SULFIDE
MIL compliance	YES
Plug information	MULTIPLE MATING PARTS AVAILABLE
Mixed contacts	NO
Installation type	CABLE AND PANEL
Options	GENERAL PURPOSE
Shell surface	GOLD
Shell material	ALUMINUM ALLOY
Housing size	G
Total number of contacts	51

Preview

Download Datasheet

View All

SHIELDING EFFECTIVENESS (Db)

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

SHIELDING EFFECTIVENESS (Db)

Micro-D Harness

EMI Performance with Ground Spring

100

1.00E+03

MWDM Micro-D

Shielded Cable Assembly

Single-Ended or Double-Ended–These

easy-to-order cable

assemblies eliminate the need for expensive assembly labor. 100%

tested and ready for use.

Now With Twisted Pairs–No

need to create a procurement

specification for Micro-D cables with twisted pairs. Glenair 177-740

cables are furnished with a full complement of white/blue twisted

pair wires.

Integral Shield Termination–The

connector shell has a platform

to accept Band-It shield termination bands. The cable shield braid is

attached directly to the connector.

Save Labor, Reduce Weight and Improve EMI Shielding

with Glenair’s Micro-D Shielded Cable Assemblies

Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s

fully shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-

piece connector shell and secured with a stainless steel

Band-Master™ ATS

clamp. These pre-wired, 100% tested

assemblies meet the requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low

shell-to-shell resistance. Available with a variety of wire types and shields, Micro-D shielded assemblies can be

ordered in any length, either single-ended or “back-to-back”.

Ground Spring and EMI Shielding Effectiveness

A gold-plated stainless steel ground spring on the pin connector mating

face offers substantial improvement in EMI protection. The graphs

compare identical connectors tested with and without ground springs.

EMI Performance without Ground Spring

100

1.00E+03

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

frequency (Hz)

High Performance Micro-D Connectors and Cables

U.S. CAGE Code 06324

Printed in U.S.A.

GLENAIR, INC.

•

1211 AIR WAY

•

GLENDALE, CA 91201-2497

•

818-247-6000

•

FAX 818-500-9912

www.glenair.com

B-14

E-Mail: sales@glenair.com

Recommended Resources

Wiring schematic diagram of a factory's secondary low-voltage power distribution panel

Touch electronic switch circuit diagram

STR80145 application circuit diagram b

555 simple and practical gust circuit

845E computer motherboard circuit diagram_38

Has anyone used Quickwave?: Has anyone used Quickwave? What are the features of this software compared with CST and Feko?...; oolv RF/Wirelessly

Problems encountered in the three-phase PFC project, please help me: Using TMS320X28121. The algorithm is voltage outer loop and current inner loop control (both are PI control), svpwm algorithm I don't understand why phase compensation is needed. How are the above thr...; li4850729 DSP and ARM Processors

The program cannot write properly to WCH's CH552 T. Please help me.: [i=s]This post was last edited by hakura on 2019-1-30 17:13[/i] I think it is difficult to read because I am using machine translation, but I would be happy if you could reply. I wrote a program for C...; hakura 51mcu

The current state of high definition: At the end of 2009, someone shouted the slogan "2010 will be the first year of high-definition". Judging from the situation in the past six months of 2010, the "first year of high-definition" is not j...; xyh_521 Industrial Control Electronics

What's wrong with my "hexadecimal to decimal function"?: In the program, AD sampling gets a hexadecimal number: #define uint16 unsigned int uint16 AD_Result=0; AD_Result=ADRESL&0x00FF; AD_Result|=ADRESH>12)&0x000f); s[1]=(((src>>8)&0x000f); s[2]=((src>>4)&0...; 面纱如雾 Microchip MCU

Verilog warning request help: Warning: Using design file convert.v, which is not specified as a design file for the current project, but contains definitions for 1 design units and 1 entities in projectInfo: Found entity 1: conver...; 不屈的生命 FPGA/CPLD

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components