INCH-POUND
MIL-M-38510/111A
10 December 2003
SUPERSEDING
MIL-M-38510/111
3 January 1979
MILITARY SPECIFICATION
MICROCIRCUITS, ANALOG SWITCH WITH DRIVER, MONOLITHIC AND MULTI-CHIP SILICON
This specification is approved for use by all Departments and Agencies of the Department of Defense.
Reactivated for new design as of 10 December 2003. May be used for either new or existing design acquisition.
1. SCOPE
1.1 Scope. This specification covers the detail requirements for silicon, break-before-make, monolithic and multi-
chip analog switches with drivers. Two product assurance classes and a choice of case outlines and lead finishes
are provided and are reflected in the complete part number. For this product, the requirements of MIL-M-38510 have
been superseded by MIL-PRF-38535, (see 6.3)
1.2 Part number. The part number should be in accordance with MIL-PRF-38535, and as specified herein.
1.2.1 Device types. The device types should be as follows:
Device type
01
02
03
04
05
06
07
08
Circuit
Dual channel, 30
Ω,
SPST switches
Dual channel, 75
Ω,
SPST switches
Dual channel, 30
Ω,
DPST switches
Dual channel, 75
Ω,
DPST switches
Single channel, 30
Ω,
SPDT switch
Single channel, 75
Ω,
SPDT switch
Dual channel, 30
Ω,
SPDT switches
Dual channel, 75
Ω,
SPDT switches
NOTE: A channel is defined as a driver with associated switches.
1.2.2 Device class. The device class should be the product assurance level as defined in MIL-PRF-38535.
1.2.3 Case outline. The case outline should be as designated in MIL-STD-1835 and as follows:
Outline letter
A 1/
C
D
E
I
X
Descriptive designator
GDFP5-F14 or CDFP6-F14
GDIP1-T14 or CDIP2-T14
GDFP1-F14 or CDFP2-F14
GDIP1-T16 or CDIP2-T16
MACY1-X10
CDFP3-F14
Terminals
14
14
14
16
10
14
Package style
Flat pack
Dual-in-line
Flat pack
Dual-in-line
Can
Flat pack
______
1/ Inactive package case outline.
Comments, suggestions, or questions on this document should be addressed to: Commander, Defense
Supply Center Columbus, ATTN: DSCC-VAS, 3990 East Broad St., Columbus, OH 43216-5000, or email
bipolar@dscc.dla.mil. Since contact information can change, you may want to verify the currency of this
address information using the ASSIST Online database at www.dodssp.daps.mil.
AMSC N/A
FSC 5962
MIL-M-38510/111A
1.3 Absolute maximum ratings.
Voltage, negative supply to positive supply [(+V
CC
) – (-V
CC
)]....................................
Voltage, drain to positive supply (+V
CC
– V
D
) ...........................................................
Voltage, negative supply to drain [V
D
– (-V
CC
)] .........................................................
Voltage, source to drain (V
D
– V
S
) ............................................................................
Voltage, negative supply to logic supply [V
L
– (-V
CC
)] ..............................................
Voltage, input to logic supply (V
L
– V
IN
) ....................................................................
Voltage, reference supply to logic supply (V
L
– V
R
) ..................................................
Voltage, reference supply to input (V
IN
– V
R
) ...........................................................
Voltage, negative supply to reference supply [V
R
–(-V
CC
)] .......................................
Voltage, input to reference supply (V
R
– V
IN
) ...........................................................
Current, any terminal ...............................................................................................
Lead temperature (soldering, 60 seconds) ...............................................................
Junction temperature ...............................................................................................
Storage temperature ................................................................................................
1.4 Recommended operating conditions.
Positive supply voltage (+V
CC
) .................................................................................
Negative supply voltage (-V
CC
) ................................................................................
Reference supply voltage (V
R
) .................................................................................
Logic supply voltage (V
L
) .........................................................................................
Ambient operating temperature range (T
A
) ..............................................................
1.5 Power and thermal characteristics.
Case outline
C, E
D, A
I
X
2. APPLICABLE DOCUMENTS
2.1 Government documents.
2.1.1 Specifications, standards, and handbooks. The following specifications and standards form a part of this
specification to the extent specified herein. Unless otherwise specified, the issues of these documents are those
listed in the issue of the Departments of Defense Index of Specifications and Standards (DODISS) and supplement
thereto, cited in the solicitation.
DEPARTMENT OF DEFENSE SPECIFICATIONS
MIL-PRF-38535
- Integrated Circuits (Microcircuits) Manufacturing, General Specification for.
Maximum allowable power dissipation
400 mW
350 mW
350 mW
300 mW
@ T
A
= 125°C
@ T
A
= 125°C
@ T
A
= 125°C
@ T
A
= 125°C
Maximum
θ
JC
35°C/W
60°C/W
40°C/W
30°C/W
Maximum
θ
JA
120°C/W
140°C/W
140°C/W
166°C/W
+15 V dc
- 15 V dc
GND
+5 V dc
-55°C
≤
T
A
≤
+125°C
36 V dc
33 V dc
33 V dc
±22
V dc
36 V dc
8 V dc
8 V dc
8 V dc
27 V dc
2 V dc
30 mA
+300°C
+175°C
-65°C to +150°C
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883
MIL-STD-1835
- Test Method Standard for Microelectronics.
- Interface Standard Electronic Component Case Outlines.
(Copies of these documents are available from the Standardization Document Order Desk, 700 Robbins Avenue,
Building 4D, Philadelphia, PA 19111-5094.
2.2 Order of precedence. In the event of a conflict between the text of this specification and the references cited
herein the text of this document shall takes precedence. Nothing in this document, however, supersedes applicable
laws and regulations unless a specific exemption has been obtained.
2
MIL-M-38510/111A
3. REQUIREMENTS
3.1 Qualification. Microcircuits furnished under this specification shall be products that are manufactured by a
manufacturer authorized by the qualifying activity for listing on the applicable qualified manufacturers list before
contract award (see 4.3 and 6.4).
3.2 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535 and as
specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the
QM plan shall not affect the form, fit, or function as described herein.
3.3 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as
specified in MIL-PRF-38535 and herein.
3.3.1 Terminal connections. The terminal connections shall be as specified on figure 1. Switch positions shown
are for a high level input logic.
3.3.2 Schematic circuits. The schematic circuits shall be maintained by the manufacturer and made available to
the qualifying activity and the preparing activity (DSCC-VA) upon request.
3.3.4 Case outlines. The case outlines shall be as specified in 1.2.3.
3.4 Lead material and finish. The lead material and finish shall be in accordance with MIL-PRF-38535 (see 6.6).
3.5 Electrical performance characteristics. The electrical performance characteristics are as specified in table I,
and apply over the full recommended ambient operating temperature range, unless otherwise specified.
3.5.1 Switch operation. The analog switches shall turn “on” with either a low input (V
R
≤
V
IL
≤
0.8 V) or a high input
(2 V
≤
V
IH
≤
V
L
) as follows:
Device type
01, 02
03, 04
05, 06
07, 08
V
IN
0.8 V dc
2.0 V dc
0.8 V dc
2.0 V dc
0.8 V dc
2.0 V dc
0.8 V dc
2.0 V dc
Switch ON
1,2
----
----
1,2,3,4
2
1
3,4
1,2
Switch OFF
----
1,2
1,2,3,4
----
1
2
1,2
3,4
3.6 Electrical test requirements. Electrical test requirements for each device class shall be the subgroups
specified in table II. The electrical tests for each subgroup are described in table III.
3.8 Marking. Marking shall be in accordance with MIL-PRF-38535.
3.9 Microcircuit group assignment. The devices covered by this specification shall be in microcircuit group number
94 (see MIL-PRF-38535, appendix A).
3
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
