EEWORLDEEWORLDEEWORLD

Part Number

Search

WBC-T0303AG-06-1320-CG

Description
Array/Network Resistor, Center Tap, Thin Film, 0.25W, 132ohm, 100V, 0.25% +/-Tol, -50,50ppm/Cel, 0303,
CategoryPassive components    The resistor   
File Size376KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance
Download Datasheet Parametric View All

WBC-T0303AG-06-1320-CG Overview

Array/Network Resistor, Center Tap, Thin Film, 0.25W, 132ohm, 100V, 0.25% +/-Tol, -50,50ppm/Cel, 0303,

WBC-T0303AG-06-1320-CG Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid802624017
Reach Compliance Codecompliant
ECCN codeEAR99
structureChip
Network TypeCenter Tap
Number of terminals6
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package length0.762 mm
Package formSMT
Package width0.762 mm
method of packingTray
Rated power dissipation(P)0.25 W
GuidelineMIL-PRF-38534
resistance132 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesWBC(TAPPED)
size code0303
technologyTHIN FILM
Temperature Coefficient50 ppm/°C
Tolerance0.25%
Operating Voltage100 V
Wire Bondable
Chip Resistors
WBC Series
Discrete or tapped schematics
MIL inspection available
High resistor density
IRC Advanced Film Division
IRC’s WBC series wire bondable chip resistors are ideally suited for
the most demanding hybrid application. The WBC combines IRC’s
TaNSil
®
tantalum nitride thin film technology with silicon substrate processing to produce an extremely small
footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil
®
resistor film.
Available in a wide range of tolerances and temperature coefficients to fit a variety of hybrid circuit applica-
tions. Custom resistance values, sizes and schematics are available on request from the factory.
Physical Data
R0202 - Discrete
(0.508mm ±0.025)
0.020˝ ±0.001
Electrical Data
Absolute Tolerance
Absolute TCR
R
Package Power Rating
(@ 70°C)
Rated Operating Voltage
(not to exceed
P x R )
Operating Temperature
Back contact
Noise
Substrate Material
Top contact
Substrate Thickness
Aluminum
Gold
R0202 and
T0303
B0202
Passivation
to ±0.1%
to ±25ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
Oxidized Silicon
(10KÅ SiO
2
min)
0.010˝ ±0.001
(0.254mm ±0.025)
10KÅ minimum
15KÅ minimum
Silicon
(Gold available)
Gold
3KÅ minimum
Silicon Dioxide or
Silicon Nitride
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
B0202 - Discrete back contact
(0.508mm ±0.025)
0.020˝ ±0.001
R
Top contact
pad chamfered
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
T0303 - Tapped network ½R + ½R
Bond Pad
Metallization
(0.762mm ±0.025)
0.030˝ ±0.001
Backside
½R
½R
0.030˝ ±0.001
(0.762mm ±0.025)
0.004˝ min bond pad size
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Email: afdsales@irctt.com • Website: www.irctt.com
A subsidiary of
TT electronics plc
WBC Series Issue April 2006
MSP430LanchPad
Error in .int06: {} > INT06 What is the reason?...
Bunny.D.CC Microcontroller MCU
How to get the data received by USB infrared adapter
I am using the IR770 USB infrared adapter from Shuimuxing. The driver is built-in with WIN XP. I can use the mobile phone to send things directly to the computer. The driver has a receiving program. N...
soszxy2008 Embedded System
Running the code reports a syntax error
When I run the code written in Verilog in Quartus2, 'Timescale 1ns/1ns always reports syntax error at EEPROM... I have been thinking about it for a long time but still can't figure out what the proble...
zhulinnchu FPGA/CPLD
Where is the keyboard driver DLL placed?
I have compiled and generated a WINCE keyboard stream interface driver MYDRIVER.DLL. Where should I put it? How to compile it into the system? Please give me some advice. I have been struggling with t...
binkeykiki Embedded System
A question about not having font library 12864
I am working on a project recently, and I use 12864 without fonts. Because there are many Chinese characters to be used, I want to implement it in this way: Use the modulus software to generate hexade...
ena MCU
I'd like some information on sate210-f, thanks!
[backcolor=rgb(238, 238, 238)][font=Tahoma, Helvetica, SimSun, sans-serif]I received a S5PV210 sate210-f board, but I can't find all the information. If any of you have bought the same board, please g...
huy666 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2794  2826  2603  2414  1194  57  53  49  25  35 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号