EEWORLDEEWORLDEEWORLD

Part Number

Search

P1206C2583BGTRE4

Description
Fixed Resistor, Thin Film, 0.33W, 258000ohm, 200V, 0.1% +/-Tol, -5,5ppm/Cel, 1206,
CategoryPassive components    The resistor   
File Size121KB,9 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Environmental Compliance
Download Datasheet Parametric View All

P1206C2583BGTRE4 Overview

Fixed Resistor, Thin Film, 0.33W, 258000ohm, 200V, 0.1% +/-Tol, -5,5ppm/Cel, 1206,

P1206C2583BGTRE4 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid827773529
Reach Compliance Codecompliant
ECCN codeEAR99
structureChip
JESD-609 codee4
Number of terminals2
Maximum operating temperature155 °C
Minimum operating temperature-55 °C
Package height0.5 mm
Package length3.06 mm
Package formSMT
Package width1.6 mm
method of packingTR
Rated power dissipation(P)0.33 W
GuidelineMIL-PRF-55342G
resistance258000 Ω
Resistor typeFIXED RESISTOR
seriesP1206
size code1206
technologyTHIN FILM
Temperature Coefficient5 ppm/°C
Terminal surfaceGold (Au) - with Nickel (Ni) barrier
Tolerance0.1%
Operating Voltage200 V
P
www.vishay.com
Vishay Sfernice
High Precision Wraparound - Wide Ohmic Value Range
Thin Film Chip Resistors
FEATURES
• Load life stability at ± 70 °C for 2000 h:
0.1 % under Pn/0.05 % under Pd
• Low temperature coefficient down to
5 ppm/°C
(- 55 °C; + 155 °C)
• Very low noise < - 35 dB and voltage coefficient
< 0.01 ppm/V
• Wide resistance range: 10
to 76 M
depending on size
• Tolerances to
± 0.01 %
For low noise and precision applications, superior stability,
low temperature coefficient of resistance, and low voltage
coefficient, Vishay Sfernice’s proven precision thin film
wraparound
resistors
exceed
requirements
of
MIL-PRF-55342G characteristics Y ± 10 ppm/°C (- 55 °C;
+ 155 °C) down to ± 5 ppm/°C (- 55 °C; + 155 °C).
• In lot tracking
5 ppm/°C
• Termination: Thin film technology
• Gold plated or pre-tinned terminations over nickel barrier
• Short circuits (jumpers) r < 50 mR, I < 2 A, see PZR
datasheet (www.vishay.com/doc?53053)
• SMD wraparound terminations
• Withstand moisture resistance test of AEC-Q200
• Compliant to RoHS Directive 2002/95/EC
Notes
*
Pb containing terminations are not RoHS compliant, exemptions
may apply
**
Please see document “Vishay Material Category Policy”:
www.vishay.com/doc?99902
DIMENSIONS
in millimeters (inches)
A
D
D
C
B
E
E
A
CASE SIZE
MAX. TOL.
+ 0.152 (+ 0.006)
MIN. TOL.
- 0.152 (- 0.006)
NOMINAL
0302
0402
0505
0603
0705/0805
1005
1206
1505
2010
0.75 (0.029)
1.00 (0.039)
1.27 (0.005)
1.52 (0.060)
1.91 (0.075)
2.54 (0.100)
3.06 (0.120)
3.81 (0.150)
5.08 (0.200)
B
MAX. TOL.
+ 0.127 (+ 0.005)
MIN. TOL.
- 0.127 (- 0.005)
NOMINAL
0.60 (0.024)
0.60 (0.024)
1.27 (0.050)
0.85 (0.033)
1.27 (0.050)
1.27 (0.050)
1.60 (0.063)
1.32 (0.052)
2.54 (0.100)
0.40 (0.016)
0.48 (0.019)
0.5 (0.02)
± 0.127 (0.005)
0.38 (0.015)
0.13 (0.005)
C
NOMINAL
0.15 (0.006)
0.25 (0.010)
D/E
TOLERANCE
0.08 (0.003)
0.1 (0.004)
Note
• Case size 2512 under development. Please consult Vishay Sfernice.
Revision: 08-Sep-11
1
For technical questions, contact:
sfer@vishay.com
Document Number: 53017
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
Does anyone know if the STM8S103F3 is compatible with the 207 series?
I debugged the program with 207 series well. (Timer 4). But it doesn't work when ported to F3. It's hard to read the manual of ST, and I can't find any detailed information. If you have used it, pleas...
?????? stm32/stm8
Newbie Question
What does the H in 00H,02H mean?...
totoro3425 Embedded System
CC3200 serial port configuration problem
Has anyone used CC3200 UART0 PIN45 (UART0_RX) and PIN53 (UART0_TX)? I am using this in a project, but it cannot be used after configuration like other pins. Is there any other configuration required t...
newfirebw TI Technology Forum
Dedicated to beginners---stm32 serial port interrupt receiving and sending routines
This example uses the serial port of stm32 to receive and send interrupts to receive a frame of data sent by the serial port debugging assistant and echoes the verification. This example allows beginn...
luhezhangjian stm32/stm8
My first experiment with actel FPGA failed. Can you help me? Thank you.
I don't know why Zhou Ligong chose actel for his FPGA and the difficult-to-use libero development environment. I'm not used to this after using Q2!The first FPGA LED program I copied from a book:modul...
小兽abc FPGA/CPLD
What are the upgrades and improvements of Altium Designer 19 compared to AD18?
RT! What are the upgrades and improvements of Altium Designer 19 compared to AD18?...
oyhprince PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1807  2368  1500  2287  466  37  48  31  47  10 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号