EEWORLDEEWORLDEEWORLD

Part Number

Search

MS27483Y12N35XD

Description
MIL Series Connector, 22 Contact(s), Stainless Steel, Male, Solder Terminal
CategoryThe connector    The connector   
File Size960KB,111 Pages
ManufacturerDefense Logistics Agency
Download Datasheet Parametric View All

MS27483Y12N35XD Overview

MIL Series Connector, 22 Contact(s), Stainless Steel, Male, Solder Terminal

MS27483Y12N35XD Parametric

Parameter NameAttribute value
Objectid1129304243
Reach Compliance Codeunknown
ECCN codeEAR99
Other featuresSTANDARD: MIL-C 38999
Rear interface of connectorNo Rear Threads
Connector insertion detailsI712
Connector typeMIL SERIES CONNECTOR
Contact point genderMALE
Contact part numberM39029/58-360
Number of contacts22
Contact size22D
Contact typeSolder Eyelet
Coupling typeBAYONET
other instructionsReceptacle, Jam Nut
Drawing date and revision17DEC99,K
Environmental characteristicsHERMETIC
waterproof levelPartial
MIL complianceYES
Manufacturer's serial numberMS27483
Military connector housingS359B
Mixed contactsNO
Maximum operating temperature200 °C
Minimum operating temperature-65 °C
Maximum plug diameter1.016 inch
polarizationD
Shell surfaceELECTRO DEPOSITED NICKEL
Shell materialSTAINLESS STEEL
Housing size12
Termination typeSOLDER
Total number of contacts22
Unique insertion number12-35
INCH-POUND
MIL-DTL-38999K
17 December 1999
SUPERSEDING
MIL-C-38999J
06 April 1990
DETAIL SPECIFICATION
CONNECTORS, ELECTRICAL, CIRCULAR, MINIATURE, HIGH DENSITY,
QUICK DISCONNECT (BAYONET, THREADED, AND BREECH COUPLING),
ENVIRONMENT RESISTANT, REMOVABLE CRIMP AND HERMETIC SOLDER CONTACTS
GENERAL SPECIFICATION FOR
This specification is approved for use by all Departments
and Agencies of the Department of Defense.
1. SCOPE
1.1 Scope. This specification covers four series of miniature, high density, bayonet, threaded, or breech
coupling, circular, environment resistant, electrical connectors using removable crimp or fixed hermetic
solder contacts, and are capable of operation within a temperature range of -65°C to +200°C (see 1.3.1d).
See 6.1 for intended use and applications.
1.2 Description. All series include rear release removable pin and socket contacts with crimp
termination. All series are designed to assure proper orientation of the mating halves prior to electrical
circuit closure. All series include hermetically sealed receptacles with fixed contacts for solder termination.
All series include EMI shielding capability. Series I, III, and IV connectors with conductive finishes provide
electrical continuity between mated shells prior to contact engagement and have the contacts so located as
to be protected from handling damage and inadvertent electrical contact. Series II provides low silhouette
for minimum size and weight and includes connectors which provide shell-to-shell electrical continuity when
mated.
1.3 Classification.
1.3.1 Connectors. Connectors fabricated to this specification are classified as follows:
a. Series: The series I, II, III, and IV connectors are not interchangeable or intermateable.
I
II
III
IV
-
-
-
-
Scoop-proof, bayonet coupling.
Non-scoop-proof, bayonet coupling, low silhouette.
Scoop-proof, triple start, self-locking, threaded coupling.
Scoop-proof, breech coupling.
Beneficial comments (recommendations, additions, deletions) and any pertinent data which may
be of use in improving this document should be addressed to: Defense Supply Center Columbus,
ATTN: VAI, 3990 East Broad Street, Columbus OH 43216-5000 by using the self-address
Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this
document or by letter.
AMSC N/A
DISTRIBUTION STATEMENT A: Approved for public release; distribution is unlimited.
FSC 5935
NXP sent me some boards to show off
I won’t show the common FDRMs, as I threw them away after playing with them for a while. I will show the rare ones....
技术范儿 NXP MCU
Prelude to eZ430-RF2500 experience
I just received the eZ430-RF2500 this morning. I uploaded a few photos as a souvenir. I would also like to thank the classmate who sent it to me for the careful packaging. I won’t say anything else. I...
梦之旅 Microcontroller MCU
List of basic instruments and main components for the 2011 National Electronic Design Competition
[i=s] This post was last edited by paulhyde on 2014-9-15 09:47 [/i] Basic instrument list 20MHz ordinary oscilloscope (dual channel, external trigger input, with X-axis input) 60MHz dual channel digit...
laoyou2010 Electronics Design Contest
Principle and Application of New Digital Temperature Sensor
[p=30, null, left][color=rgb(43, 43, 43)][font=Arial, 宋体]With the rapid development of sensor technology, the new digital temperature sensors provided by many modern sensor companies have the characte...
chuandong Sensor
Some questions about DMA in ZStack
Due to work needs, the serial communication between the ZIGBEE module and the PC uses the DMA method. Use the PC to set the following functions to the ZIGBEE module through the serial port: 1). Set th...
yangfan370683 RF/Wirelessly
Comparative analysis of several LED protection circuit design solutions
White light LED is a voltage-sensitive device. In actual operation, the upper limit of the current is 20mA. However, the current often increases due to various reasons during use. If no protective mea...
qwqwqw2088 LED Zone

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2224  1236  1698  143  2780  45  25  35  3  56 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号