EEWORLDEEWORLDEEWORLD

Part Number

Search

CH133B2G-EPD-BA

Description
Board Connector, 33 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Receptacle
CategoryThe connector    The connector   
File Size172KB,2 Pages
ManufacturerTeka Interconnection Systems
Download Datasheet Parametric View All

CH133B2G-EPD-BA Overview

Board Connector, 33 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Receptacle

CH133B2G-EPD-BA Parametric

Parameter NameAttribute value
MakerTeka Interconnection Systems
Reach Compliance Codeunknow
ECCN codeEAR99
Other featuresWITH SOLDER CLIPS
body width0.1 inch
subject depth0.12 inch
body length3.3 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU ON NI
Contact completed and terminatedGOLD
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
insulator materialTHERMOPLASTIC
Manufacturer's serial numberCH
Plug contact pitch0.1 inch
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
PCB contact patternRECTANGULAR
Plating thickness10u inch
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.105 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts33
Base Number Matches1
Check out the new post function, everyone take a look~~~
Previously, Blue Eye Fox and wangjiafu1985 suggested that the forum should have a function to view new posts. This function was added today:As shown in the figure: Label 1 remains the same, including ...
soso Suggestions & Announcements
Winding inductance of electrolytic capacitor
The electrolytic capacitor is made of two strips of aluminum foil with insulating paper. Because it is wound, it is considered to be an inductor. This conclusion has been circulated for decades. I don...
PowerAnts Analog electronics
As a beginner, how can I learn the relevant knowledge of WINCE?
Since I will be going to the company for internship in two months, the engineer from the relevant department of the company informed me that I should first familiarize myself with the wince system and...
t63056 Embedded System
How does COMBOBOX get focus?
I want to do something when COMBOBOX gets the focus. The method I used is if(GetFoucs()->GetDlgCtrlID==IDC_XXX), but the cursor is clearly on COMBOBOX but it doesn't seem to get the focus. The same co...
2002xiao Embedded System
I have some questions about a small program and need some advice
module count4(out,reset,clk); output[3:0] out; input[3:0] reset,clk; reg[3:0] out; always @(posedge clk)beginif(reset) out=0;else out=out+1;end endmoduleIs the reason why out is defined as a register ...
leomeng FPGA/CPLD
2440, bootloader problem
My bsp contains stepldr and eboot, I want to run eboot, but after burning stepldr.nb1 into flash, dnw shows garbled characters! ! ! ! This is the initial code of the serial port: void Uart_Init(void) ...
ricky03221115 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 664  868  885  2478  676  14  18  50  45  58 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号