EEWORLDEEWORLDEEWORLD

Part Number

Search

D55342E07B13Y2PWPM

Description
Fixed Resistor, Thin Film, 0.25W, 13200ohm, 100V, 0.5% +/-Tol, 25ppm/Cel, Surface Mount, 1206, CHIP
CategoryPassive components    The resistor   
File Size96KB,5 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

D55342E07B13Y2PWPM Overview

Fixed Resistor, Thin Film, 0.25W, 13200ohm, 100V, 0.5% +/-Tol, 25ppm/Cel, Surface Mount, 1206, CHIP

D55342E07B13Y2PWPM Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid145080522743
package instructionCHIP
Reach Compliance Codenot_compliant
ECCN codeEAR99
structureRectangular
JESD-609 codee0
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-65 °C
Package height0.8382 mm
Package length3.2004 mm
Package formSMT
Package width1.6002 mm
method of packingWaffle Pack
Rated power dissipation(P)0.25 W
Rated temperature70 °C
GuidelineMIL-PRF-55342
resistance13200 Ω
Resistor typeFIXED RESISTOR
size code1206
surface mountYES
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Terminal surfaceTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Terminal shapeWRAPAROUND
Tolerance0.5%
Operating Voltage100 V
E/H (Military M/D55342)
www.vishay.com
Vishay Dale Thin Film
QPL MIL-PRF-55342 Qualified
Thin Film Resistor, Surface-Mount Chip
FEATURES
• Established reliability, “S” and “V” failure rate level
(10 ppm), C = 2
• High purity alumina substrate
• Wraparound termination featuring a tenacious adhesion
layer covered with an electroplated nickel barrier layer for
+150 °C operating conditions
LINKS TO ADDITIONAL RESOURCES
• Very low noise and voltage coefficient
(< -25 dB, 0.5 ppm/V)
• Non-inductive
• Laser-trimmed tolerances ± 0.1 %
• Wraparound resistance less than 0.010
Ω
typical
• In-lot tracking less than 5 ppm/°C
• Complete MIL-testing available in-house
• Antistatic waffle pack or tape and reel packaging available
• Military / aerospace / QPL
D
D
3
3
3D Models
Thin Film Mil chip resistors feature all sputtered wraparound
termination for excellent adhesion and dimensional
uniformity. They are ideal in applications requiring stringent
performance requirements. Established reliability is assured
through 100 % screening and extensive environmental lot
testing.
CONSTRUCTION
Passivation
Resistor Film
Solder
Coating
Nickel Barrier
High Purity
Alumina Substrate
Adhesion Layer
TYPICAL PERFORMANCE
ABSOLUTE
TCR
TOL.
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Resistance Range
TCR: Absolute
Tolerance: Absolute
Stability: Absolute
Stability: Ratio
Voltage Coefficient
Working Voltage
Operating Temperature Range
Storage Temperature Range
Noise
Shelf Life Stability: Absolute
SPECIFICATIONS
Tamelox resistor film (passivated nichrome)
10
Ω
to 6.19 MΩ
± 25 ppm/°C to ± 300 ppm/°C
± 0.1 %, ± 0.25 %, ± 0.5 %, ± 1 %,
± 2 %, 5 %, ± 10 %
ΔR
± 0.02 %
-
0.1 ppm/V
30 V to 200 V
-65 °C to +150 °C
-65 °C to +150 °C
< - 25 dB
ΔR
± 0.01 %
CONDITIONS
-
-
-55 °C to +125 °C
+25 °C
2000 h at +70 °C
-
-
-
-
-
-
1 year at +25 °C
Revision: 15-Nov-2021
Document Number: 60018
1
For technical questions, contact:
thinfilm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
3C lithium battery development trend
3C electronic products such as mobile phones, tablets, and laptops have a large demand for battery life, and lithium cobalt oxide batteries have the best volume energy density ratio, so they are most ...
kzt Power technology
Building the MSP430 Launchpad development environment under Linux
I set up the IAR development environment according to the method on the Internet, and tried to run a program to light up the lights. It was very smooth, but the problem also came. The drivers on my Wi...
qinkaiabc Microcontroller MCU
Problems and analysis during ise synthesis
question: The code was successfully debugged in QuartusII. When ported to ISE, the following warning appeared during synthesis : WARNING:Par:288 - The signal clk_IBUF has no load. PAR will not attempt...
eeleader FPGA/CPLD
How to view the string transmitted by UART in Tiva launchpad
I am new to launchpad and want to use the serial port to transmit strings. I would like to know how to test and view the transmitted values. Should I use the serial port debugging tool like the 51 mac...
刘浩辰 Microcontroller MCU
RP2040 Lightsaber
A Star Wars lightsaber made by the official Raspberry Pi team, programmed with RP2040 and CircuitPython.https://www.raspberrypi.com/news/new-toby-made-us-rp2040-lightsabers-for-silicon/...
dcexpert MicroPython Open Source section
AT32F425-Evaluation Report-USB Communication 06
Brief description This series is based on the evaluation report of the Ateli-AT32F425R8T7-7 development boardObjective: Test the USB communication routines of the official website and understand the c...
维尔瓦 Domestic Chip Exchange

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1237  1120  2555  1235  12  25  23  52  1  29 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号