EEWORLDEEWORLDEEWORLD

Part Number

Search

D55342E07B1B29RT1

Description
RESISTOR, THIN FILM, 0.25 W, 0.1 %, 25 ppm, 1290 ohm, SURFACE MOUNT, 1206, CHIP
CategoryPassive components    The resistor   
File Size98KB,4 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

D55342E07B1B29RT1 Overview

RESISTOR, THIN FILM, 0.25 W, 0.1 %, 25 ppm, 1290 ohm, SURFACE MOUNT, 1206, CHIP

D55342E07B1B29RT1 Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
Objectid1761456402
package instructionSMT, 1206
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresNON-INDUCTIIVE, LASER TRIMMABLE
structureRectangular
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package height0.254 mm
Package length3.2 mm
Package formSMT
Package width1.6 mm
method of packingTR
Rated power dissipation(P)0.25 W
Rated temperature70 °C
GuidelineMIL-PRF-55342
resistance1290 Ω
Resistor typeFIXED RESISTOR
size code1206
surface mountYES
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Terminal shapeWRAPAROUND
Tolerance0.1%
Operating Voltage100 V
E/H (Military M/D55342)
www.vishay.com
Vishay Dale Thin Film
QPL MIL-PRF-55342 Qualified
Thin Film Resistor, Surface-Mount Chip
FEATURES
• Established reliability, “S” and “V” failure rate level
(10 ppm), C = 2
• High purity alumina substrate
• Wraparound termination featuring a tenacious adhesion
layer covered with an electroplated nickel barrier layer for
+150 °C operating conditions
LINKS TO ADDITIONAL RESOURCES
D
D
3
3
3D Models
• Very low noise and voltage coefficient
(< -25 dB, 0.5 ppm/V)
• Non-inductive
• Laser-trimmed tolerances ± 0.1 %
• Wraparound resistance less than 0.010
typical
• In-lot tracking less than 5 ppm/°C
• Complete MIL-testing available in-house
• Antistatic waffle pack or tape and reel packaging available
• Military / aerospace / QPL
Thin Film Mil chip resistors feature all sputtered wraparound
termination for excellent adhesion and dimensional
uniformity. They are ideal in applications requiring stringent
performance requirements. Established reliability is assured
through 100 % screening and extensive environmental lot
testing.
CONSTRUCTION
Passivation
Resistor Film
Solder
Coating
Nickel Barrier
High Purity
Alumina Substrate
Adhesion Layer
TYPICAL PERFORMANCE
ABSOLUTE
TCR
TOL.
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Resistance Range
TCR: Absolute
Tolerance: Absolute
Stability: Absolute
Stability: Ratio
Voltage Coefficient
Working Voltage
Operating Temperature Range
Storage Temperature Range
Noise
Shelf Life Stability: Absolute
SPECIFICATIONS
Tamelox resistor film (passivated nichrome)
10
to 6.19 M
± 25 ppm/°C to ± 300 ppm/°C
± 0.1 % to ± 10 %
R
± 0.02 %
-
0.1 ppm/V
30 V to 200 V
-55 °C to +150 °C
-55 °C to +150 °C
< - 25 dB
R
± 0.01 %
CONDITIONS
-
-
-55 °C to +125 °C
+25 °C
2000 h at +70 °C
-
-
-
-
-
-
1 year at +25 °C
Revision: 14-May-2020
Document Number: 60018
1
For technical questions, contact:
thinfilm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
PLC Programming Software
I just started to learn PLC programming. Can anyone send me some PLC programming software? Thanks!!! My email address is [email=luckydechun@yahoo.cn]luckydechun@yahoo.cn[/email]...
haibian826 MCU
Request 100-240v to dc24v3.5a power supply design
[i=s] This post was last edited by Heishitou1981 on 2018-5-24 23:46 [/i] I want a 100-240v to dc24v3.5a power supply design. The simpler the better. The board is only 80mm*85mm. The input voltage is 1...
黑石头1981 Power technology
Qingyuefeng function introduction - absolute eccentric pad processing function
[size=10.5pt][font=宋体][size=4]The processing of eccentric pads is actually a very practical technology. In high-end PCB software design, there is a function of eccentric processing. However, some comm...
tsingyue PCB Design
Please advise on the periodic execution of tasks (the period is less than the system stick)
If the system stick is 10ms, what should I do if a task needs to ensure a 4.8ms execution cycle? Thank you in advance....
hyw322 Embedded System
Text editor issues
I copied the project code to a mobile hard disk, and then took it out from the mobile hard disk. I want to select variables, but every time the text editor selects 1 line, it selects the spaces. I wou...
不足论 Embedded System
About the problem of designing triggers with two statements in Verilog
This question started when I first came into contact with Verilog. When using the always statement to design a D flip-flop, the existing flip-flop will be directly called during synthesis. What will h...
htrong8899 FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1837  2597  2125  139  591  37  53  43  3  12 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号