EEWORLDEEWORLDEEWORLD

Part Number

Search

NJ7N80F-LI

Description
7.0A 800V N-CHANNEL POWER MOSFET
File Size615KB,6 Pages
ManufacturerNanjing International Group Co.,Ltd
Download Datasheet View All

NJ7N80F-LI Overview

7.0A 800V N-CHANNEL POWER MOSFET

NJ7N80F-LI Preview

Download Datasheet
NJ7N80 POWER MOSFET
7.0A 800V N-CHANNEL POWER MOSFET
DESCRIPTION
The NJ7N80 is an N-channel mode power MOSFET using
advanced technology to provide customers with planar stripe and DMOS
technology. This technology specializes in allowing a minimum
on-state resistance and superior switching performance. It also can
withstand high energy pulse in the avalanche and commutation mode.
The NJ7N80 is universally applied in high efficiency switch mode power supply.
FEATURES
* V
DS
=
800V
* I
D
=
7.0A
*
RDS(on)=1.8
ohm@VGS
=10V
*
High switching speed
*
100% avalanche tested
1
TO-220
1
TO-220F
SYMBOL
ORDERING INFORMATION
Ordering Number
NJ7N80-LI
NJ7N80-BL
NJ7N80F-LI
Package
TO-220
TO-220
TO-220F
Pin Assignment
1
2
3
G
D
S
G
D
S
G
D
S
Packing
Tape
Box
Bulk
Tube
Note:
Pin Assignment: G: Gate
D: Drain
S: Source
Does anyone have relevant information on FPGA-based CRC hardware module IP design? ? ?
Does anyone have relevant information on CRC hardware module IP design based on FPGA? ? ? I hope you can give me some advice and relevant information! Thank you very much!...
hefeifei1990 FPGA/CPLD
Repost: FW: The jokes we made when we were young and ignorant and just went abroad
1. Once, the landlord asked me, did you eat anyting yet? I said no. After hearing this, she repeated it again, so u didn't eat anyting. I said yes... The old landlord hesitated and asked again, did yo...
shuangshumei Talking
CC2630 chip cannot be recognized during programming
The software used is Smart Flash Programmer2. The simulation burning tool is XDS100V3. The board programming port is VCC-GND-TMS-TCK-RESET. You can use it without RESET. Just connect the board to the ...
fish001 Wireless Connectivity
[Help] Hardware IIC slave problem of stm8s103f3p6
Dear experts, I encountered a problem when debugging the iic slave of stm8. When the host sends the device number and address, the slave responds to ack normally, but when the host starts to read data...
kiverin stm32/stm8
cc1100 Help, urgent! Thank you!
I don't know what's wrong with my program. CC1100 just can't configure registers and write values to registers! SpiWriteReg(CC1100_FSCTRL1, 0x08); SpiWriteReg(CC1100_FSCTRL0, 0x00); SpiWriteReg(CC1100...
dx2004025 RF/Wirelessly
Celebrating the forum's new version
Warmly celebrate the forum revision...
njlianjian MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

About Us Customer Service Contact Information Datasheet Sitemap LatestNews

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190

Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号