(5 ±1 seconds and charge/discharge not exceeding 50 mA)
0.1%
1,000 megohm microfarads or 100 GΩ
(Rated voltage applied for 120 ±5 seconds @ 25°C)
Parameters/Characteristics
To obtain IR limit, divide MΩ-µF value by the capacitance and compare to GΩ limit. Select the lower of the two limits.
Capacitance and dissipation factor (DF) measured under the following conditions:
1 MHz ±100 kHz and 1.0 ±0.2 Vrms if capacitance ≤ 1,000 pF
1 kHz ±50 Hz and 1.0 ±0.2 Vrms if capacitance > 1,000 pF
Note: When measuring capacitance it is important to ensure the set voltage level is held constant. The HP4284 and Agilent E4980 have a feature known as
Automatic Level Control (ALC). The ALC feature should be switched to "ON."
Post Environmental Limits
High Temperature Life, Biased Humidity, Moisture Resistance
I am new to MP3 and would like to know some development questions: 1. Development process 2. Compile, debug, and burn steps 2. Which variables are applied by yourself 3. How to call the interface pict...
The power supplies required by DSP are 3.3V and 1.8V. If different power supplies are used, are there any special requirements for the power-on sequence?...
The forum finally has an Altera event. I am so happy. However, the last question is not mentioned in the article, but I found it in this article [b]Altera SoC FPGA: The Importance of Architecture[/b] ...
The original text is described as follows: 2pin current loop sensors (ABS-type with 7/14mA output signal). Could you please tell me the principle or information of this sensor? Thank you...
[table=98%] [tr][td][color=#000000]Summary of common errors encountered during DSP application development: 1.warning: entry point symbol _c_int00 undefined When using C to write DSP programs, the ent...
Entering the information age after the millennium, the huge demand for semiconductor chips has made China the world's largest semiconductor market. According to relevant data, the scale of my count...[Details]
The most significant event in the technology circle during this period is undoubtedly the news that ZTE was banned by the United States. Once the news came out, it shocked the entire Chinese techno...[Details]
On April 20, Alibaba Group announced that it would acquire
the
chip
company Zhongtian Microelectronics and invest in six
chip
companies. Yesterday, JD.com CEO Liu Qiangdong said in a...[Details]
In the actual project development process, hardware circuits often need to be modified, and the modified parts need to modify the driver. Thinking about the coming and going of such requirements is t...[Details]
The program got stuck during LCD initialization. Through hardware debugging, it was found that it was stuck in the Delay_ms() function. Going to the definition, it was found to be a macro definition ...[Details]
In the previous article, I wrote a simple GPIO running light test, which looked a bit monotonous. I was used to serial port debugging. If there was no serial port on the board, I had to find another ...[Details]
In 1952, Bell Labs built a 6-foot-tall automatic number recognition machine called "Audrey", which could recognize the pronunciation of the numbers 0 to 9 with an accuracy of more than 90%. And its...[Details]
A few days ago, Hanergy Chairman Li held a grand launch of Hanwa new products, which once again attracted the attention of the mass media to the development of photovoltaics. The unique Hanergy has gr...[Details]
When designing a product, if the application environment's requirements for power isolation are not considered, the product will be unstable due to improper design, and even high voltage may damage t...[Details]
1. Introduction to MC68K CPU The MC683xx series of microcontrollers are composed of the famous MOTOROLA 32-bit microprocessors such as MC68K, 68020, 68040, and the compatible 68K, CPU32, CPU3...[Details]
What are your expectations and ideas
for
the future of
Xiaomi Mi Band
?
Xiaomi Mi Band’s
official Weibo shared many netizens’ thoughts on
the future direction and functions
of Xiao...[Details]
12864 LCD parallel port driver is more commonly used, but considering that sometimes the IO port of the microcontroller or MCU is limited, the serial driver method can be used. The following is ...[Details]
It is required to use MCS-51 microcontroller to sort data. 1. Sort the 8 data in ascending order; 2. The data to be sorted is stored in the internal data memory address units 30H-37H, which are 34H, ...[Details]
Please help me analyze the clock cycles occupied by the following delay program. Seek to explain: DELAY: MOV R6, #13 DELAY1: MOV R5, #250 DELAY2: NOP DJNZ R5, DELAY2 DJNZ R6, DEL...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
