Features ....................................................................................................................................................................................... 1
Typical Phase Jitter (70 fs RMS) and Phase Noise Data ............................................................................................................. 2
Ordering Information .................................................................................................................................................................... 3
LVPECL and FlexSwing Termination .................................................................................................................................. 19
LVDS, Supply Voltage: 1.8 V
±5%,
2.5 V ±10%, 3.3 V ±10%, 2.25 V to 3.63 V, 1.71 V to 3.63 V ...................................... 20
HCSL, Supply Voltage: 1.8 V
±5%,
2.5 V ±10%, 3.3 V ±10%, 2.25 V to 3.63 V, 1.71 V to 3.63 V ...................................... 20
Low-power HCSL, Supply Voltage: 1.8 V
±5%,
2.5 V ±10%, 3.3 V ±10%, 2.25 V to 3.63 V, 1.71 V to 3.63 V .................... 20
Dimensions and Patterns ― 2.0 x 1.6 mm x mm ....................................................................................................................... 21
Dimensions and Patterns ― 2.5 x 2.0 mm x mm ....................................................................................................................... 22
Dimensions and Patterns ― 3.2 x 2.5 mm x mm ....................................................................................................................... 23
Revision History ......................................................................................................................................................................... 24
Rev 0.54
Page 4 of 25
www.sitime.com
SiT9501
Ultra-low Jitter Differential XO for Standard Networking Frequencies
Electrical Characteristics
ADVANCED
All Min and Max limits in the Electrical Characteristics tables are specified over operating temperature and rated operating
voltage with standard output termination shown in the termination diagrams. Typical values are at 25°C and nominal
supply voltage.
Table 3. Electrical Characteristics – Common to All Output Signaling Types
Parameter
Output Frequency Range
Symbol
f
Min.
Typ.
Max.
Unit
MHz
Condition
Refer to frequencies listed in
Error! Not a valid result for table.
s
ection.
Inclusive of initial tolerance, operating temperature, rated power
supply voltage, load variation of 15 pF
±
10%, and 10 years
aging at 25°C
Inclusive of initial tolerance, operating temperature, rated power
supply voltage, load variation of 15 pF
±
10%, and first year aging
at 25°C
Ambient temperature of 25°C
Extended commercial, ambient temperature
Industrial, ambient temperature
Ambient temperature
Extended industrial, ambient temperature
Voltage-supply order code “YY”
Voltage-supply order code “XX”
Voltage-supply order code “18”.
Contact SiTime
for 1.5 V
Voltage-supply order code “25”
Voltage-supply order code “33”
Pins 1 and 2 for OE and SE, respectively
Pins 1 and 2 for OE and SE, respectively
Pins 1 and 2 for OE and SE, respectively
See
Figure 6
and
Figure 8
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin toggles to enable logic level to
the time clock pins reach 90% of swing. See
Figure 13
Measured from the time OE pin toggles to disable logic level to
the last clock edge. See
Figure 14
12 kHz to 20 MHz offset frequency integration bandwidth
Our company wants to make a washing machine, but I don't know how to write control algorithms, so I bought a development board.The development board is a speed closed loop. I heard that the washing ma...
Let me talk about my personal situation first: I have been working for almost three years. I have seen all the languages and used all the technologies. I can basically take on projects on my own for a...
I am new to ARM and I have a question. I would like to ask an expert for help. The following is the statement: movs r9,r9,lsr #1 bcs %F1 add r8,r8,#4 b %B0 What does B %B0 stand for?...
Location: Beijing Requirements: ? More than 2 years of experience in WHQL testing, strong WHQL problem diagnosis and analysis capabilities, and in-depth research on Microsoft MDA ? More than 1 year of...
This is A's success [code]/****************POWSOS__430************************ Program function: Dynamically display the text "welcome" ---------------------------------------------------- Test instru...
Motor Drive Control（Motor Control）
京公网安备 11010802033920号
EEWORLD
