FT24C04A-ULR-T datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > FT24C04A-ULR-T

Preview

FT24C04A-ULR-T: DescriptionTwo-Wire Serial EEPROM 4K, 8K and 16K (8-bit wide); File Size283KB，20 Pages; ManufacturerETC2

Download Datasheet Compare View All

FT24C04A-ULR-T Overview

Two-Wire Serial EEPROM 4K, 8K and 16K (8-bit wide)

Preview

Download Datasheet

View All

24C04A, 24C08A, 24C16A

Two-Wire Serial EEPROM

4K, 8K and 16K (8-bit wide)

FEATURES



Low voltage and low power operations:



FT24C04A/08A/16A:

= 1.8V to 5.5V

Maximum Standby current < 1µA (typically 0.02µA and 0.06µA

1.8V and 5.5V respectively).

16 bytes page write mode.

Partial page write operation allowed.

Internally organized: 512



8 (4K), 1024



8 (8K), 2048



8 (16K).

Standard 2-wire bi-directional serial interface.

Schmitt trigger, filtered inputs for noise protection.

Self-timed Write Cycle (5ms maximum).

1 MHz (5V), 400 kHz (1.8V, 2.5V, 2.7V) Compatibility.

Automatic erase before write operation.

Write protect pin for hardware data protection.

High reliability: typically 1, 000,000 cycles endurance.

100 years data retention.

Industrial temperature range (-40

C to 85

C).

Standard 8-pin DIP/SOP/TSSOP/DFN/MSOP and 5-pin SOT-23/TSOT-23 Pb-free packages.



DESCRIPTION

The FT24C04A/08A/16A series are 4096/8192/16384 bits of serial Electrical Erasable and Programmable Read Only

Memory, commonly known as EEPROM. They are organized as 512/1024/2048 words of 8 bits (1 byte) each. The

devices are fabricated with proprietary advanced CMOS process for low power and low voltage applications. These

devices are available in standard 8-lead DIP, 8-lead SOP, 8-lead TSSOP, 8-lead DFN, 8-lead MSOP, and 5-lead SOT-

23/TSOT-23 packages. A standard 2-wire serial interface is used to address all read and write functions. Our

extended V

range (1.8V to 5.5V) devices enables wide spectrum of applications.

PIN CONFIGURATION

Pin Name

A2, A1, A0

SDA

SCL

Pin Function

Device Address Inputs

Serial Data Input / Open Drain Output

Serial Clock Input

Write Protect

No-Connect

DS3001M-page1

24C04A, 24C08A, 24C16A

DEVICE ADDRESSING

The 2-wire serial bus protocol mandates an 8 bits device address word after a START bit condition to invoke valid read

or write command. The first four most significant bits of the device address must be 1010, which is common to all

serial EEPROM devices. The next three bits are device address bits. These three device address bits (5

, 6

and 7

) are

to match with the external chip select/address pin states. If a match is made, the EEPROM device outputs an

ACKNOWLEDGE signal after the 8

read/write bit, otherwise the chip will go into STANDBY mode. However,

matching may not be needed for some or all device address bits (5

, 6

and 7

) as noted below. The last or 8th bit is a

read/write command bit. If the 8th bit is at V

then the chip goes into read mode. If a “0” is detected, the device enters

programming mode.

FT24C04A uses A2 (5

) and A1 (6

) device address bits. Only four FT24C04A devices can be wired-OR on the same

2-wire bus. Their corresponding chip select address pins A2 and A1 must be hard wired and coded from 00 (b) to 11

(b). Chip select address pin A0 is not used.

FT24C08A uses only A2 (5

) device address bit. Only two FT24C08A devices can be wired-OR on the same 2-wire

bus. Their corresponding chip select address pin A2 must be hard-wired and coded from 0 (b) to 1 (b). Chip select

address pins A1 and A0 are not used.

FT24C16A does not use any device address bit. Only one FT24C16A device can be used on the on 2-wire bus. Chip

Select address pins A2, A1, and A0 are not used.

WRITE OPERATIONS

(A) BYTE WRITE

A byte write operation starts when a micro-controller sends a START bit condition, follows by a proper EEPROM

device address and then a write command. If the device address bits match the chip select address, the EEPROM

device will acknowledge at the 9

clock cycle. The micro-controller will then send the rest of the lower 8 bits word

address. At the 18

cycle, the EEPROM will acknowledge the 8-bit address word. The micro-controller will then

transmit the 8 bit data. Following an ACKNOWLDEGE signal from the EEPROM at the 27

clock cycle, the

micro-controller will issue a STOP bit. After receiving the STOP bit, the EEPROM will go into a self-timed

programming mode during which all external inputs will be disabled. After a programming time of T

, the byte

programming will finish and the EEPROM device will return to the STANDBY mode.

(B) PAGE WRITE

A page write is similar to a byte write with the exception that one to sixteen bytes can be programmed along the

same page or memory row. All FT24C04A/08A/16A are organized to have 16 bytes per memory row or page.

With the same write command as the byte write, the micro-controller does not issue a STOP bit after sending the

byte data and receiving the ACKNOWLEDGE signal from the EEPROM on the 27

clock cycle. Instead it

sends out a second 8-bit data word, with the EEPROM acknowledging at the 36

cycle. This data sending and

EEPROM acknowledging cycle repeats until the micro-controller sends a STOP bit after the n



clock cycle.

After which the EEPROM device will go into a self-timed partial or full page programming mode. After the page

programming completes after a time of T

, the devices will return to the STANDBY mode.

DS3001M-page5

FT24C04A-ULR-T Related Products

	FT24C04A-ULR-T	24C04A	24C16A
Description	Two-Wire Serial EEPROM 4K, 8K and 16K (8-bit wide)	The FT24C04A/08A/16A series are 4096/8192/16384 bits of serial Electrical Erasable and Programmable Read Only Memory, commonly known as EEPROM. They are organized as 512/1024/2048 words of 8 bits (1 byte) each.	Two-Wire Serial EEPROM 4K, 8K and 16K (8-bit wide)

Recommended Resources

Basic circuit of differential amplifier circuit

Ground conductivity measurement circuit

Tube amplifier CS8412+SM5853+PCM58 circuit diagram

TV audio infrared transponder circuit

555 infrared transmitter circuit

Bridge tube high voltage rectifier circuit

AVR MCU Hardware and Software Design Tutorial: [size=6][color=red]AVR MCU Hardware and Software Design Tutorial, PPT Document[/color][/size]...; lyf19842008 Microchip MCU

ADI16365 Data Sheet: Please download if needed...; fl090726 ADI Reference Circuit

[Raspberry Pi Pico Review]——by fxyc87: @fxyc87[Raspberry Pi Pico Review] - Unboxing + Download [Raspberry Pi Pico Review] - Start Programming [Raspberry Pi Pico Review] - Start compiling the program 2 [Raspberry Pi Pico Review] - How to sa...; okhxyyo DIY/Open Source Hardware

High score for wireless network data transmission problem: I want to use the 802.11 protocol to perform point-to-point data transmission between two laptops, based on a C/S structure, with one laptop running a server program and the other laptop running a cli...; 思想者 Embedded System

Is it necessary to set GPIOF4 high when booting from flash?: After the flash was successfully burned, I suddenly remembered that the GPIOF4 pin on my board was not set high.I read in most materials that if you want to boot from flash, you must set GPIOF4 high.N...; lijiamin11 Microcontroller MCU

What issues regarding antenna isolation should we pay attention to?: This article will be divided into three parts to explain the definition of antenna isolation, several key factors affecting antenna isolation, and how to improve the isolation of terminal antennas. I ...; btty038 RF/Wirelessly

Shortcut: 00 01 02 03 04 05 06 07 08 09 0A 0C 0F 0J 0L 0M 0R 0S 0T 0Z 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 1H 1K 1M 1N 1P 1S 1T 1V 1X 1Z 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 2G 2K 2M 2N 2P 2Q 2R 2S 2T 2W 2Z 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 3G 3H 3J 3K 3L 3M 3N 3P 3R 3S 3T 3V 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4M 4N 4P 4S 4T 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5E 5G 5H 5K 5M 5N 5P 5S 5T 5V 60 61 62 63 64 65 66 67 68 69 6A 6C 6E 6F 6M 6N 6P 6R 6S 6T 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7M 7N 7P 7Q 7V 7W 7X 80 81 82 83 84 85 86 87 88 89 8A 8D 8E 8L 8N 8P 8S 8T 8W 8Y 8Z 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9F 9G 9H 9L 9S 9T 9W

Popular Components