EEWORLDEEWORLDEEWORLD

Part Number

Search

PPC1/2251241D13

Description
RESISTOR, METAL GLAZE/THICK FILM, 0.5W, 0.5%, 25ppm, 1240ohm, SURFACE MOUNT, 2008, MELF
CategoryPassive components    The resistor   
File Size178KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

PPC1/2251241D13 Overview

RESISTOR, METAL GLAZE/THICK FILM, 0.5W, 0.5%, 25ppm, 1240ohm, SURFACE MOUNT, 2008, MELF

PPC1/2251241D13 Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
Objectid1981549063
package instructionMELF
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresPRECISION
JESD-609 codee0
Manufacturer's serial numberPPC
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Package shapeCYLINDRICAL PACKAGE
method of packingTR, 13 INCH
Rated power dissipation(P)0.5 W
Rated temperature70 °C
resistance1240 Ω
Resistor typeFIXED RESISTOR
size code2008
surface mountYES
technologyMETAL GLAZE/THICK FILM
Temperature Coefficient25 ppm/°C
Terminal surfaceTin/Lead (Sn/Pb)
Terminal shapeWRAPAROUND
Tolerance0.5%
Operating Voltage300 V
Metal Glaze
Surface Mount
Precision Power Chip
PPC Series
Surge tolerant
Up to 1000 volts
Tight TCR - 25 ppm/°C
Tolerance down to ±0.1%
Solder over nickel
barrier
High
temperature
dielectric
coating
Metal Glaze™ thick
film element fired
at 1000°C to solid
ceramic substrate
Electrical Data
Size
Code
B
D
F
H
Industry
Footprint
1206
2010
2512
3610
IRC
Type
PPC1/8
PPC1/2
PPC1
PPC2
Power
Rating at
70°C (W)
1/8 W
1/2 W
1W
2W 1.33W
Working
Voltage
200
300
350
500
Resistance
Range
(ohms)
100 - 10K
100 - 10K
100 - 10K
100 - 10K
0.1% (B)
0.25% (C)
0.5% (D)
Tolerance
(±%)
Qty /
Reel (7")
2500
1500
N/A
N/A
Qty /
Reel (13")
10000
5000
5000
1500
Environmental Data
Characteristics
Temperature Coefficient
Thermal Shock
Low Temperature Operation
Short Time Overload
High Temperature Exposure
Resistance to Bonding
Exposure
Solderability
Moisture Resistance
Life Test
Terminal Adhesion Strength
Maximum Change
As specified
±0.5% + 0.01 ohm
±0.25% + 0.01 ohm
±0.5% + 0.01 ohm
±0.5% + 0.01 ohm
±0.25% + 0.01 ohm
95% minimum coverage
±0.5% + 0.01 ohm
±0.5% + 0.01 ohm
±1% + 0.01 ohm
±1% + 0.01 ohm
no mechanical damage
Test Method
MIL-R-55342E Par 4.7.9 (-55°C + 125°C)
MIL-R-55342E Par 4.7.3 (-65°C + 150°C, 5 cycles)
MIL-R-55342E Par 4.7.4 (-65°C @ working voltage)
MIL-R-55342E Par 4.7.5 2.5 x
for 5 seconds
MIL-R-55342E Par 4.7.6 (+150°C for 100 hours)
MIL-R-55342E Par 4.7.7 (Reflow soldered to board at 260°C
for 10 seconds)
MIL-STD-202, Method 208 (245°C for 5 seconds)
MIL-R-55342E Par 4.7.8 (10 cycles, total 240 hours)
MIL-R-55342E Par 4.7.10 (2000 hours at 70°C intermittent)
1200 gram push from underside of mounted chip for 60
seconds
Chip mounted in center of 90mm long board, deflected 1mm
so as to exert pull on chip contacts for 5 seconds
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
Wire and Film Technologies Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
PPC Series Issue November 2008 Sheet 1 of 3
Design experience of benq Taiwan organization engineers (Part 2)
The mobile phones that hw is responsible for can be dropped directly to the ground, but the projectors that chris is responsible for are expensive, so the drop test method must be used to avoid the hi...
songbo RF/Wirelessly
How will 3D integrated circuits be realized simultaneously? (Repost)
How will 3D integrated circuits be realized simultaneously? Author: Philip Garrou Microelectronic Consultants of North Carolina Research Triangle Park, NC 2009-03-03 Hits: 1660 The first commercial ap...
jyl PCB Design
RS48 parallel garbled code problem
[i=s] This post was last edited by kkkwgwk0083 on 2018-7-26 17:58 [/i] @chunyang, moderator, please help me, I will be grateful. Problem description. There are two RS485 communication boards, and the ...
kkkwgwk0083 Test/Measurement
[Help Post] High-frequency oscillation of high-frequency switching power supply current
A 100W wireless power transmission prototype was made before. The primary resonant side adopted full-bridge switch phase shift control. The schematic diagram is shown in the figure.The actual measured...
shzhbchina Power technology
Pre-registration for the live broadcast with prizes: TI's latest application of millimeter-wave radar in the automotive field
Register for live broadcast Live broadcast time Tuesday, May 25, 10:00-11:30 a.m. Live Topic TI's latest applications of millimeter-wave radar in the automotive field Live content Introduces the lates...
EEWORLD社区 Automotive Electronics
IAR compile error at Medium optimization level
I encountered a strange problem today. IAR had a problem when compiling. (IAR version is V5.40, optimization level is Medium) The C code is #define UART_ENABLE {UCA1CTL1 |= UCSWRST;P4SEL |= (BIT4|BIT5...
lqh07153 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1662  2757  23  599  893  34  56  1  13  18 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号