The 3.3V pin header on the lower right corner of the C2000 was accidentally connected to 15V, and then I checked and found that the 3.3V output terminal and the ground were broken. What might be burne...
[media=swf,700,475]http://www.tudou.com/v/vISzN1bReag/&rpid=106547959&resourceId=106547959_04_05_99/v.swf[/media] [[i] This post was last edited by qinkaiabc on 2013-3-18 12:43[/i]]...
[size=3] I am very happy to have won the qualification to participate in the "GigaDevice GD32E231 DIY Competition". I would like to take this opportunity to express my gratitude to the organizers of t...
GAM-60 solder paste mixer (made in Taiwan)GAM-60 Description:1. Easy to operate, place the solder paste dispenser on the universal fixture, set the mixing time and press the start button, it will stop...
After nearly a week of porting, uC/OS-II finally ran normally on the development board. The small LED light flashed at 5Hz, which was so dazzling and beautiful... Cortex-M4 is also an upgraded product...
There is a WIFI switch on a WINCE device, which is used to control the connection and disconnection of WIFI. Are the functions of obtaining all WIFI hotspots, connecting to a hotspot, determining whet...
Assume that data is read from 8-bit AD (if it is a higher-bit AD, the data type can be defined as int), the subroutine is get_ad();
1. Limited secondary filtering
/* A value can be adjust...[Details]
0. Introduction
In daily life, we often see some special-purpose vehicles. When these vehicles pass through intersections, they often obtain the right of way at intersections by temporarily op...[Details]
Floating-point digital signal processing has become a constant requirement for precision technology, often in applications requiring high accuracy in areas such as aviation, industrial machinery, a...[Details]
1 Introduction
Solar street lights are mainly composed of four parts: solar photovoltaic cell components, batteries, charge and discharge controllers, and lighting fixtures. The bo...[Details]
We know that microcontroller development tools generally include real-time online emulators and programmers. Among them, online emulators are very good tools, but they are also more expensive...[Details]
Overview
In spectral measurement, photomultiplier tubes (PMT) and charge-coupled devices (CCD) are often used as photoelectric converters. PMT is used in slow-changing, high-precision spectral...[Details]
Motors are important products that convert electrical energy into mechanical energy to achieve automation, and they are widely used in industrial control, medical electronics, white a...[Details]
LED is now known as the fourth generation of light sources. High-power LED has many advantages over traditional light sources in outdoor lighting.
1 LED lamps have high light efficiency
C...[Details]
1 Load Regulation
Changes in power supply load will cause changes in power supply output. When the load increases, the output decreases, and vice versa, when the load decreases, the output inc...[Details]
The most important components of new energy electric vehicles are power batteries, electric motors and energy conversion control systems. The power battery must achieve high performance such as fas...[Details]
This article focuses on closing the feedback loop of an isolated power supply using a TL431 shunt regulator. The article discusses a method to extend the bandwidth of the power supply control loop ...[Details]
1. Introduction
AS-Interface bus technology is an intelligent network that uses a single cable to connect sensors and actuators to controllers, transmit data, and provide power. It can be used...[Details]
The biggest advantage of Profibus is that it is guaranteed by the stable international standard EN50170 and has been proven to be universal in practical applications. It has been widely used in man...[Details]
The programmable controller directly controls the stepper motor, which can significantly reduce the cost of the control system of the modular machine tool automatic production line. The article int...[Details]
In recent years, the application of single-chip microcomputer systems in the field of industrial measurement and control has become more and more extensive. However, for industrial sites with harsh...[Details]