EEWORLDEEWORLDEEWORLD

Part Number

Search

WBC-T0303GG-07-2492-FJ

Description
Array/Network Resistor, Center Tap, Thin Film, 0.25W, 24900ohm, 100V, 1% +/-Tol, -25,25ppm/Cel, 0303,
CategoryPassive components    The resistor   
File Size376KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance
Download Datasheet Parametric View All

WBC-T0303GG-07-2492-FJ Overview

Array/Network Resistor, Center Tap, Thin Film, 0.25W, 24900ohm, 100V, 1% +/-Tol, -25,25ppm/Cel, 0303,

WBC-T0303GG-07-2492-FJ Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid802713757
Reach Compliance Codecompliant
ECCN codeEAR99
structureChip
Network TypeCenter Tap
Number of terminals6
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package length0.762 mm
Package formSMT
Package width0.762 mm
method of packingTray
Rated power dissipation(P)0.25 W
GuidelineMIL-PRF-38534
resistance24900 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesWBC(TAPPED)
size code0303
technologyTHIN FILM
Temperature Coefficient-25,25 ppm/°C
Tolerance1%
Operating Voltage100 V
Wire Bondable
Chip Resistors
WBC Series
Discrete or tapped schematics
MIL inspection available
High resistor density
IRC Advanced Film Division
IRC’s WBC series wire bondable chip resistors are ideally suited for
the most demanding hybrid application. The WBC combines IRC’s
TaNSil
®
tantalum nitride thin film technology with silicon substrate processing to produce an extremely small
footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil
®
resistor film.
Available in a wide range of tolerances and temperature coefficients to fit a variety of hybrid circuit applica-
tions. Custom resistance values, sizes and schematics are available on request from the factory.
Physical Data
R0202 - Discrete
(0.508mm ±0.025)
0.020˝ ±0.001
Electrical Data
Absolute Tolerance
Absolute TCR
R
Package Power Rating
(@ 70°C)
Rated Operating Voltage
(not to exceed
P x R )
Operating Temperature
Back contact
Noise
Substrate Material
Top contact
Substrate Thickness
Aluminum
Gold
R0202 and
T0303
B0202
Passivation
to ±0.1%
to ±25ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
Oxidized Silicon
(10KÅ SiO
2
min)
0.010˝ ±0.001
(0.254mm ±0.025)
10KÅ minimum
15KÅ minimum
Silicon
(Gold available)
Gold
3KÅ minimum
Silicon Dioxide or
Silicon Nitride
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
B0202 - Discrete back contact
(0.508mm ±0.025)
0.020˝ ±0.001
R
Top contact
pad chamfered
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
T0303 - Tapped network ½R + ½R
Bond Pad
Metallization
(0.762mm ±0.025)
0.030˝ ±0.001
Backside
½R
½R
0.030˝ ±0.001
(0.762mm ±0.025)
0.004˝ min bond pad size
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Email: afdsales@irctt.com • Website: www.irctt.com
A subsidiary of
TT electronics plc
WBC Series Issue April 2006
How to improve reliability in FPGA board design?
Everyone is welcome to speak!...
eeleader FPGA/CPLD
A single-stage power factor correction circuit with constant power control
A single-stage power factor correction circuit with constant power control Abstract: A single-stage power factor correction circuit with constant power control is proposed. The power factor correction...
zbz0529 Industrial Control Electronics
Reprinted------Transformer Same Name Terminal Detection Method
I find it very useful, so I’d like to share it with you....
lovelee Integrated technical exchanges
How to develop GPS and what equipment is needed? How to choose GPS module and MCU
I am studying GPS devices recently, but I don't know what kind of development board I need to develop GPS. How to choose GPS module and MCU? Are there any standards? Can anyone with development experi...
wangxuguang150 Embedded System
Why does the transceiver use a bitslip module at the receiving end and how to implement it?
RT. The altlvds_tx and altlvds_rx cores are used. After the serial-to-parallel conversion at the receiving end, a bitslip module is used. It seems to have completed a bit shift function. I don't quite...
robertslyh FPGA/CPLD
Please help
I just registered and don’t know how to get this chip coin, eh!...
xzhxcf PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1359  1034  523  2848  1551  28  21  11  58  32 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号