EEWORLDEEWORLDEEWORLD

Part Number

Search

D55342K07B246USTP

Description
Fixed Resistor, Thin Film, 0.25W, 246000ohm, 100V, 0.25% +/-Tol, 100ppm/Cel, Surface Mount, 1206, CHIP
CategoryPassive components    The resistor   
File Size98KB,4 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

D55342K07B246USTP Overview

Fixed Resistor, Thin Film, 0.25W, 246000ohm, 100V, 0.25% +/-Tol, 100ppm/Cel, Surface Mount, 1206, CHIP

D55342K07B246USTP Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid145088963016
package instructionCHIP
Reach Compliance Codenot_compliant
ECCN codeEAR99
Other featuresNON-INDUCTIVE
structureRectangular
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package height0.254 mm
Package length3.2 mm
Package formSMT
Package width1.6 mm
method of packingTR
Rated power dissipation(P)0.25 W
Rated temperature70 °C
GuidelineMIL-PRF-55342
resistance246000 Ω
Resistor typeFIXED RESISTOR
size code1206
surface mountYES
technologyTHIN FILM
Temperature Coefficient100 ppm/°C
Terminal shapeWRAPAROUND
Tolerance0.25%
Operating Voltage100 V
E/H (Military M/D55342)
www.vishay.com
Vishay Dale Thin Film
QPL MIL-PRF-55342 Qualified
Thin Film Resistor, Surface-Mount Chip
FEATURES
• Established reliability, “S” and “V” failure rate level
(10 ppm), C = 2
• High purity alumina substrate
• Wraparound termination featuring a tenacious adhesion
layer covered with an electroplated nickel barrier layer for
+150 °C operating conditions
LINKS TO ADDITIONAL RESOURCES
D
D
3
3
3D Models
• Very low noise and voltage coefficient
(< -25 dB, 0.5 ppm/V)
• Non-inductive
• Laser-trimmed tolerances ± 0.1 %
• Wraparound resistance less than 0.010
typical
• In-lot tracking less than 5 ppm/°C
• Complete MIL-testing available in-house
• Antistatic waffle pack or tape and reel packaging available
• Military / aerospace / QPL
Thin Film Mil chip resistors feature all sputtered wraparound
termination for excellent adhesion and dimensional
uniformity. They are ideal in applications requiring stringent
performance requirements. Established reliability is assured
through 100 % screening and extensive environmental lot
testing.
CONSTRUCTION
Passivation
Resistor Film
Solder
Coating
Nickel Barrier
High Purity
Alumina Substrate
Adhesion Layer
TYPICAL PERFORMANCE
ABSOLUTE
TCR
TOL.
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Resistance Range
TCR: Absolute
Tolerance: Absolute
Stability: Absolute
Stability: Ratio
Voltage Coefficient
Working Voltage
Operating Temperature Range
Storage Temperature Range
Noise
Shelf Life Stability: Absolute
SPECIFICATIONS
Tamelox resistor film (passivated nichrome)
10
to 6.19 M
± 25 ppm/°C to ± 300 ppm/°C
± 0.1 % to ± 10 %
R
± 0.02 %
-
0.1 ppm/V
30 V to 200 V
-55 °C to +150 °C
-55 °C to +150 °C
< - 25 dB
R
± 0.01 %
CONDITIONS
-
-
-55 °C to +125 °C
+25 °C
2000 h at +70 °C
-
-
-
-
-
-
1 year at +25 °C
Revision: 14-May-2020
Document Number: 60018
1
For technical questions, contact:
thinfilm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
When learning STM chips, should we use firmware library or register programming?
RT, I did a project last year using a firmware library, which was not very difficult, but I didn’t know the underlying operations and there were many versions of the firmware library. This year I am u...
qq21497936 stm32/stm8
NRF24L01 Wireless Module
[i=s]This post was last edited by paulhyde on 2014-9-15 09:24[/i] As the title...
wqyheya Electronics Design Contest
The difference between sampleapp and genericapp in serial communication
I developed a small project on sampleapp before, and used serial port input to control the change of LED, but I found that I could not get the correct result. The serial port debugging assistant did n...
mr_j RF/Wirelessly
About MPC8270 SPI driver
I wrote a section of SPI driver code today. The board uses SPI to operate a FLASH. MPC is the master and FLASH is the slave. Below is my code, which is mainly the initialization of some registers. Thi...
foster Embedded System
LSM6DSL Minimum Evaluation Board
...
littleshrimp MEMS sensors
How to print text via Bluetooth printer in Windows CE 6.0
Now ce6.0 has connected to the printer via bluetooth, I don't know how to send the print command, as long as it can print text. The printer is tsc m23 portable, the bluetooth port is com9. Thanks for ...
2008pcu Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 197  8  2555  1937  1110  4  1  52  40  23 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号