EEWORLDEEWORLDEEWORLD

Part Number

Search

SFP12702BEAGHWS

Description
Fixed Resistor, Thin Film, 0.25W, 127000ohm, 100V, 0.1% +/-Tol, -25,25ppm/Cel, 0202,
CategoryPassive components    The resistor   
File Size85KB,3 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

SFP12702BEAGHWS Overview

Fixed Resistor, Thin Film, 0.25W, 127000ohm, 100V, 0.1% +/-Tol, -25,25ppm/Cel, 0202,

SFP12702BEAGHWS Parametric

Parameter NameAttribute value
Objectid992789325
Reach Compliance Codeunknown
ECCN codeEAR99
structureChip
Number of terminals2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height0.254 mm
Package length0.558 mm
Package formSMT
Package width0.558 mm
method of packingWaffle Pack
Rated power dissipation(P)0.25 W
resistance127000 Ω
Resistor typeFIXED RESISTOR
seriesSFP
size code0202
technologyTHIN FILM
Temperature Coefficient-25,25 ppm/°C
Tolerance0.1%
Operating Voltage100 V
SFP
www.vishay.com
Vishay Electro-Films
Thin Film Top-Contact Resistor with Part Mark
FEATURES
• Wire bondable
• Part marked - 5 digits
• Small size: 0.022 inches square
• Case: 0202
• Resistance range: 1
to 1 M
Product may not be to scale
The SFP series single-value resistor chips offer a small size,
wide ohmic value range and excellent power capacity.
The SFPs are part marked with resistance value allowing
user the ability to visually determine the resistance value of
the chip.
The SFPs are manufactured using Vishay Electro-Films (EFI)
sophisticated thin film equipment and manufacturing
technology.
The SFPs are 100 % electrically tested and visually
inspected to MIL-STD-883, method 2032 class H or K.
• DC power rating: 250 mW
• Oxidized silicon substrate for good power dissipation
• Resistor material: Tantalum nitride, self passivating
• Moisture resistant
APPLICATIONS
Vishay EFI SFP small resistor chips are widely used in hybrid
packages where space is limited and chip value marking is
important for identification. The die is part marked with the
resistance value. Wire bonding is made to the two pads on
the top of the chip.
TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES, AND TOLERANCES
PARAMETER
Total Resistance Range
Standard Tolerances
TCR
VALUE
1 to 1M
± 0.1, ± 0.5, ± 1
± 25, ± 50, ± 100, ± 250
Tightest Standard Tolerance Available
1%
0.5 %
0.1 %
± 25 ppm/°C
± 50 ppm/°C
± 100 ppm/°C
± 250 ppm/°C
UNIT
%
ppm/°C
1
Ω
10
Ω
30
Ω
100
Ω
200 k
Ω
430 k
Ω
620 k
Ω
1 M
Ω
STANDARD ELECTRICAL SPECIFICATIONS
PARAMETER
Noise, MIL-STD-202, Method 308
100
- 250 k
< 100
or > 251 k
Moisture Resistance, MIL-STD-202, Method 106
Stability, 1000 h, + 125 °C, 125 mW
Operating Temperature Range
Thermal Shock, MIL-STD-202, Method 107, Test Condition F
High Temperature Exposure, + 150 °C, 100 h
Dielectric Voltage Breakdown
Insulation Resistance
Operating Voltage
DC Power Rating at + 70 °C (Derated to zero at + 175 °C)
5 x Rated Power Short-Time Overload, + 25 °C, 5 s
Note
• Values above 1M available
Revision: 15-Aug-11
1
For technical questions, contact:
efi@vishay.com
VALUE
- 35 typ.
- 20 typ.
± 0.5 max.
R/R
± 0.25 max.
R/R
- 55 to + 125
± 0.25 max.
R/R
± 0.5 max.
R/R
200
10
12
min.
100 V max.
0.250
± 0.25 max.
R/R
UNIT
dB
%
%
°C
%
%
V
V
W
%
Document Number: 61000
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
What filter is suitable for DDS?
Hello everyone: The DDS I am using now is AD9833. As shown in the figure above, the output uses an inverting amplifier to amplify the sine wave, but I found that the waveform has a sawtooth component....
PSIR Analog electronics
Issues to pay attention to in PCB design
Priority, control line, memory, wiring Issues to be noted in PCB design The purpose of PCB design should be clear. For important signal lines, the length of wiring and processing ground loops should b...
xhxyd PCB Design
How to program a microcontroller well (8)
15. The Cultivation of Modifying Other People's Programs ------------ When you maintain other people's programs, please do not delete or modify existing programs in a very subjective way. I often see ...
yuandayuan6999 MCU
stm8 detects the falling edge of the port pulse
A square wave pulse enters the port. Now we need to determine its falling edge. Which one takes less time, external interrupt or input capture?...
sang523 stm32/stm8
Question about the working state of TTL inverter transistor
In this figure, when the input voltage is a high level of 3.6V, why are T2 and T3 in a saturated state instead of an amplified state?...
pvnana Analog electronics
How to select the pop-up interface mode
Now I am developing a PDA using WIN CE. I want to pop up a pre-set interface by clicking a certain button. How can I set it up? As a cutting version, the smart device form is too different from creati...
ydm123ydm Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1793  1769  488  720  1694  37  36  10  15  35 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号