Standard Frequencies – see Page 5 for developed frequencies.
* Check with factory for availability of frequencies not listed.
Applications
Automotive Electronics
Mobile Multimedia/Infotainment
Car Navigation Systems
Internet of Things [IoT, IIot]
Microcontrollers and FPGAs
Wireless Communication
Ethernet/GbE/SyncE
Medical Electronics
Commercial Military & Aerospace
Description
CTS Model SA254 incorporates a low cost, high Q, small size quartz resonator specifically developed to operate
over extended temperature ranges for use in automotive electronics.
Ordering Information
Model
SA254
Frequency Code
[MHz]
XXX
Mode of
Oscillation
F
Tolerance
@ +25°C
3
Temperature
Stability
5
Temperature
Range
G
Load
Capacitance
A
Packaging
R
Code
Frequency
Product Frequency Code
1
Code
1
X
2
3
5
Tolerance
±10ppm
±15ppm
±20ppm
±30ppm
±50ppm
Code
I
G
H
N
P
M
Stability
±15ppm
±20ppm
±30ppm
Code
5
6
7
Temp. Range
2
-40°C to +85°C
-40°C to +105°C
3
4
-40°C to +125°C
-40°C to +150°C
5
5
-55°C to +105°C
-55°C to +125°C
5
Packing
Code
3k pcs./reel
R
Code
F
Mode
Fundamental
Code
X
2
3
Stability
±50ppm
±100ppm
±150ppm
Code Capacitance Code Capacitance
7pF
16pF
V
C
8pF
18pF
K
D
9pF
20pF
J
E
10pF
24pF
A
F
12pF
30pF
L
G
13pF
Series
B
S
Notes:
1]
2]
3]
4]
5]
Refer to document 016-1454-0, Frequency Code Tables. 3-digits for frequencies <100MHz, 4-digits for frequencies 100MHz or greater.
Available with all stability codes.
Available with stability codes 3, 5, 6 and 7.
Available with stability codes 5, 6 and 7.
Stability codes 6 and 7. Contact factory for code 5 availability.
Not all performance combinations and frequencies may be available.
Contact your local CTS Representative or CTS Customer Service for availability.
This product is specified for use only in standard commercial applications. Supplier disclaims all express and implied warranties and liability in connection with any use of this
product in any non-commercial applications or in any application that may expose the product to conditions that are outside of the tolerances provided in its specification.
[i=s]This post was last edited by dmzdmz666666 on 2021-4-21 22:57[/i]After receiving the development board and unpacking it, we can officially develop this open board. First, I will look for the offic...
This semester, I learned about computer organization and design. Regarding the single-cycle implementation of MIPS, there is a question that I have not figured out, so I came here to ask the experts f...
Are there any textbooks that can be recommended regarding the design basis for line width, safety distance, vias, and pads during circuit board design? In order to find the mathematical basis during t...
When using the serial port, are the serial port driver stream interface functions open to users, that is, the functions under the MDD part, including COM_Init, COM_Deinit, COM_Open, COM_Close, COM_Rea...
I need to make a small thing, similar to a development board. It has 5 switch inputs, 4 relay outputs, 2 lights, and displays the status through a 6-digit digital tube. The program is very simple, whi...
Introduction
FPGA designs are vulnerable to design theft because configuration bitstreams can be easily captured and copied.FPGAs are more vulnerable to cloning of the entire design rather than to int...
In recent years, as energy consumption and environmental protection issues have attracted people's attention, my country's solar photovoltaic power generation industry has shown a rapid development...[Details]
Event: The company simultaneously released its 2017 annual report and the first quarter report of 2018. In 2017, the company achieved revenue of 8.886 billion yuan, a year-on-year increase of 48.01...[Details]
1. Problem When developing STM32 with IAR, I found that I could not print floating point numbers by redirecting printf to the serial port. The code is as follows: The output is as follows: It can...[Details]
1. Test conditions Hardware: STM32L432KC Main frequency: 80MHz Compiler: IAR 8.20.1 Compiler options: High Speed no size constraints CRC generator polynomial: 0x782f 2. Test Method The softwar...[Details]
For STM32, there are two ways to reset the software: 1) Use the official software library The system reset function is directly provided in the stm32f10x_nvic.c file of the official software li...[Details]
When Amazon launched its first
cloud computing
service, the outside world was not optimistic about this direction, as it had high investment, low profits and many uncertainties. Let's follo...[Details]
stm32cubeMX graphical configuration content STM32CubeMX is part of the original STMCube initiative from st microelectronics, and STM32Cube includes STM32CubeMX. STM32CubeMX is a graphical software co...[Details]
This is my first time writing an STM32 program. I have many questions to ask. I want to convert the data of the SO of MAX6675 into the actual temperature and read it out using the serial port tool. I...[Details]
In the development of artificial intelligence, talent reserve is undoubtedly an important part. Artificial intelligence should be a bottom-level technology that can be deeply embedded in any indust...[Details]
The application of millimeter wave technology in mobile communications also involves a series of technical problems, including the large propagation loss of millimeter waves and the susceptibility ...[Details]
Leading Chinese PV inverter manufacturer Huawei said it is supplying string inverters to a 75MW fully digital utility-scale solar project in Brazil, which it claims is the first of its kind in the cou...[Details]
What is SYSTICK: This is a 24-bit system tick timer, SysTick, with automatic reload and overflow interrupt functions. All microcontrollers based on the Cortex_M3 processor can obtain a certain time ...[Details]
As photovoltaic power stations come into people's view, people are paying more and more attention to them. Recently, some netizens asked me how to match the inverter and components of photovoltaic ...[Details]
At the beginning, I used the stdlib library. Recently, I found that the cube library is more and more widely used, so I started to use the cube library to complete the ADC multi-channel acquisition e...[Details]
Independent watchdog (IWDG) and low power mode are often used in STM32 development. The watchdog is to detect and solve faults caused by software errors, and the low power mode is to enter sleep mode...[Details]
Domestic Chip Exchange
京公网安备 11010802033920号
EEWORLD
