227T1012S320SN datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Mechanical and electronic products> switch> 227T1012S320SN

227T1012S320SN: DescriptionRotary Switch, 12 Positions, 10P12T, Latched, 1A, 28VDC, Solder Terminal, Panel Mount-threaded, ROHS COMPLIANT; CategoryMechanical and electronic products switch; File Size333KB，3 Pages; ManufacturerCTS; Environmental Compliance

Download Datasheet Parametric View All

227T1012S320SN Overview

Rotary Switch, 12 Positions, 10P12T, Latched, 1A, 28VDC, Solder Terminal, Panel Mount-threaded, ROHS COMPLIANT

227T1012S320SN Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
package instruction	ROHS COMPLIANT
Reach Compliance Code	unknow
ECCN code	EAR99
Body length or diameter	33.32 mm
Contact (AC) maximum rated R load	.75A@125VAC
Maximum contact current (AC)	0.75 A
Maximum contact current (DC)	1 A
Contact (DC) maximum rated R load	1A@28VDC
Maximum contact voltage (AC)	125 V
Maximum contact voltage (DC)	28 V
Electrical life	25000 Cycle(s)
Graduation angle	30 deg
JESD-609 code	e4
Manufacturer's serial number	227T
Installation features	PANEL MOUNT-THREADED
Number of positions	12
Number of switching segments	1
surface mount	NO
Switch action	LATCHED
switch function	10P12T
Switch type	ROTARY SWITCH
Terminal surface	Silver (Ag)
Termination type	SOLDER
Base Number Matches	1

Preview

Download Datasheet

View All

Series 227

Data Sheet

Electrocomponents

Rotary Switch

Industrial

Features

• Hill and valley detent

• Enclosed diecast detent plate

• Low cost

• 30˚ indexing

Rotary Switch

• Solder lug and printed circuit terminals available

• Molded stator prevents solder from flowing into

the circuit

• Custom switching patterns available

• Index or wafers are available separately

• RoHS compliant

Electrical and Mechanical Specifications

Indexing

Double bump spring hill and valley detent with

30° indexing for 2 through 12 positions or

continuous rotation.

Voltage and Contact Rating

UL Rating: 3/4 amp at 125 VAC (shorting type only)

Special Rating: 1/4 amp at 28 VDC (shorting or non shorting)

1 amp at 28 VDC (shorting type only)

Contact Resistance

.015 ohm max. when measured from adjacent terminals

Stop Strength

15 in-lb (17.3 Kgf-cm)

Torque

As required within a range of 10 in-oz. (720 gf-cm)

to 60 in-oz. (4.3 Kgf-cm)

Detent Rotational Life

25,000 cycles

Materials

Shaft: Aluminum or brass at CTS option

Bushing: Brass or Zinc diecast at CTS option

Detent Spring: Stainless steel

Detent Plate: Zinc diecast

Rotor Contacts, Stator Contacts and Terminals:

Silver plated brass standard

Stator Insulator: Glass reinforced thermoset material

Bushing Lengths

Standard: 3/8"-32 UNEF-2A Thread,1/4" (6.35mm)

or 3/8" (9.53mm) long.

Special Lengths: Available as required

Locating Lugs

Standard: Left side .531" (13.5mm) radius

Special: Right side .531" (13.5mm) radius or no lug

Shaft Trim

Standard: Plain round, Flat, Slot, Knurl, or mixed (Flat with Slot)

Special: Available as required

Frames

Machine screw, or staked strut (up to 3 wafers only)

Technical Data Sheet 1448C

1-3

CTS Electrocomponents

09/13/09

www.ctscorp.com

Recommended Resources

Use MC34063 as a 12-volt programming power supply for single-chip microcomputer

Principle circuit diagram of three basic working modes of non-isolated switching power supply

On-site signal optical fiber transmission and reception circuit

555DC electronic mousetrap circuit

Relay delay suction circuit

Lathe no-load automatic shutdown power-saving circuit (1)

Development board android (4.5 install ubuntu patch): [font=宋体]xsltproc ia32-libs libgl1-mesa-dri:i386 lib32ncurses5-dev lib32z1-dev uboot-mkimage This patch cannot be installed. Is the installation package broken? I downloaded it using WIFI, which ultim...; 亮痕 Embedded System

Problems installing glib: When I installed glib, I had no problem downloading and unzipping. There was no error in ./configure either, but an error occurred during make, as shown in the figure:Please give me some advice, thank...; chenbingjy Linux and Android

TI's C6000 series DSP, implementation of flashboot: The so-called flashboot is to burn the user's main program into the flash chip, and then power on to realize the automatic loading and startup process of the main program. This article does not discus...; Aguilera DSP and ARM Processors

Do you understand? dBm, dBV, dBuv, dB, dBf and other measurement units: [i=s]This post was last edited by dontium on 2015-1-23 11:24[/i] [b][size=3]Explain the meaning of measurement units such as dBm, dBV, dBuv, dB, dBf, etc.[/size][/b] The meaning of dB1. dB is basicall...; qwqwqw2088 Analogue and Mixed Signal

In 28335epwm, the frequency and amplitude of the triangular carrier will change at the same time. Do you agree with this point of view?: The epwm addition and subtraction counting mode of 28335 generates a triangular carrier. There will be a problem. After the system clock frequency and the frequency division coefficient are fixed, the...; jonny0811 Microcontroller MCU

What is PENA in the technical manual spnu515c.pdf of TMS570LS1227? ? ?: What is PENA in the flowchart under 25.2 Quick Start Guide in the technical manual spnu515c.pdf of TMS570LS1227? ? ? I searched on Baidu, but there is no simple explanation. I don’t know if my search ...; dnmy_2017dy TI Technology Forum

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components