AC0019-2-01-16-A1 datasheet, PDF

AC0019-2-01-16-A1: DescriptionBoard Connector, 16 Contact(s), 1 Row(s), Male, Right Angle, 0.1 inch Pitch, Solder Terminal, Receptacle; CategoryThe connector The connector; File Size36KB，1 Pages; ManufacturerTechwin Opto-Electronics Co., Ltd.

Download Datasheet Parametric View All

AC0019-2-01-16-A1 Overview

Board Connector, 16 Contact(s), 1 Row(s), Male, Right Angle, 0.1 inch Pitch, Solder Terminal, Receptacle

Parameter Name	Attribute value
Objectid	304084392
Reach Compliance Code	unknown
ECCN code	EAR99
body width	0.1 inch
subject depth	0.161 inch
body length	1.6 inch
Body/casing type	RECEPTACLE
Connector type	BOARD CONNECTOR
Contact to complete cooperation	AU
Contact completed and terminated	GOLD
Contact point gender	MALE
Contact material	BRASS
contact mode	RECTANGULAR
Contact resistance	30 mΩ
Contact style	RND PIN-SKT
Dielectric withstand voltage	800VAC V
Insulation resistance	1000000000 Ω
insulator material	GLASS FILLED POLYBUTYLENE TEREPHTHALATE
Manufacturer's serial number	AC0019
Plug contact pitch	0.1 inch
Installation method	RIGHT ANGLE
Installation type	BOARD
Number of connectors	ONE
PCB row number	1
Number of rows loaded	1
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
PCB contact pattern	RECTANGULAR
Rated current (signal)	3 A
reliability	COMMERCIAL
Terminal length	0.138 inch
Terminal pitch	2.54 mm
Termination type	SOLDER
Total number of contacts	16

Solution to the problem that the flying wires in PCB are not displayed: First: Click the "L" shortcut key to enter View Configurations. Make sure this option is checked. Second: If the drop-down list in PCB is in the *From-To Editor* state,...; yichun417 PCB Design

MSP430 clock interrupt enters abnormality: [backcolor=white]The following code function P1.0 outputs ACLK clock, P2.0 is used as capture pin, captures the signal of P1.0, and is triggered by the rising edge. In the capture interrupt, character...; kui Microcontroller MCU

I have finished the serial port driver, and will start working on the SD card driver tomorrow. Can you provide me with some information?: As the title says, it took me two weeks to finally get the serial port driver working. Now my serial port 1 and serial port 2 can send and receive data from the outside world normally. Tomorrow I will...; happyboy22 Embedded System

Is smart home far away from us?: [i=s]This post was last edited by jameswangsynnex on 2015-3-3 19:57[/i] 　　Nowadays, it is common for families to have multiple TVs. What should family members do if they want to watch digital pay TV i...; songbo Mobile and portable

Why do we need to enable the JTAG pull-up resistor in the 8962 can_device_qs routine?: Why do we need to enable the JTAG pull-up resistor in the 8962 can_device_qs routine?// // Enable the pull-ups on the JTAG signals. // SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOC); GPIOPadConfigSet(GPI...; academic Microcontroller MCU

A new round of group buying will start next week!: Attention all forum users , we will organize a group purchase of TI development boards next week !This group purchase requires that you post no less than 3 technical posts in the TI community !Before ...; maylove Microcontroller MCU

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components