EEWORLDEEWORLDEEWORLD

Part Number

Search

220-16E16-6P4

Description
Circular Connector, 6 Contact(s), Steel, Male, Solder Terminal, Plug
CategoryThe connector    The connector   
File Size55KB,1 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Download Datasheet Parametric View All

220-16E16-6P4 Overview

Circular Connector, 6 Contact(s), Steel, Male, Solder Terminal, Plug

220-16E16-6P4 Parametric

Parameter NameAttribute value
Reach Compliance Codecompli
Other featuresPOLARIZED, SEAL MATERIAL: FLUOROSILICONE RUBBER, CONTACT MATERIAL: NICKEL COPPER, PRESSURE RATE: 5000 PSI/345 BAR
Body/casing typePLUG
Connector typeCIRCULAR CONNECTOR
Contact point genderMALE
Coupling typeTHREADED
DIN complianceNO
IEC complianceNO
MIL complianceNO
Manufacturer's serial number22
Installation typeCABLE
OptionsWATERPROOF
Shell materialSTEEL
Termination typeSOLDER
Total number of contacts6
Base Number Matches1
9b96's Ethernet communication problem - waiting online
[color=rgb(0,0,0)][color=rgb(68,68,68)][backcolor=rgb(255,255,255)][color=rgb(68,68,68)][backcolor=rgb(255,255,255)]It is no problem to make a single program for sending data (receiving by the compute...
oyueyueniao Microcontroller MCU
Urgent!!!! Who can help me??? About CC2650 download problem??
I bought the CC2650SmartRF06 development board from TI. Can any expert tell me whether it can be downloaded using the Linux command line, just the Linux command line? Can you give me detailed steps an...
596937862 RF/Wirelessly
How to deal with impedance continuity of PCB traces?
[i=s]This post was last edited by qwqwqw2088 on 2020-12-16 07:46[/i]Everyone knows that impedance should be continuous. However, as Luo Yonghao said, "There are always times in life when you step on s...
qwqwqw2088 PCB Design
How to realize the fixed angle rotation of the smart car
Dear seniors, I am not clear about something, please give me some advice... How can I realize the intelligent car to rotate a fixed angle, such as turning left 90 degrees, etc. My car uses two reducti...
bank19841014 Embedded System
[Design Tips] How to configure UART and GPIO of SAM D and AVR
[size=4][b] Interface configuration is always a design step, but it is often cumbersome. [/b][/size] [size=4][b] Below Atmel engineers teach you the most commonly used GPIO and UART, and use the most ...
DreamerJane Microchip MCU
【Learning experience + MCU】TIVAC course is so good
The lecturer is Jin Yaer, who sounds like a foreigner. Today I watched the low power experiment 6. From preparation to success, including precautions, it is very detailed. I have to say it is a very g...
ddllxxrr Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2073  105  843  354  310  42  3  17  8  7 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号