(when high voltage is applied) for greater throughput
during system production. Protects first or last sector
regardless of sector protection settings
— Hardware reset input (RESET#) resets device
— Ready/Busy# output (RY/BY#) detects program or
erase cycle completion
Performance Characteristics
High performance
— 80 ns access time (S29GL128N, S29GL256N),
90 ns access time (S29GL512N)
— 8-word/16-byte page read buffer
— 25 ns page read times
— 16-word/32-byte write buffer reduces overall
programming time for multiple-word updates
Low power consumption (typical values at 3.0 V, 5
MHz)
— 25 mA typical active read current;
— 50 mA typical erase/program current
— 1 µA typical standby mode current
Package options
— 56-pin TSOP
— 64-ball Fortified BGA
Publication Number
27631
Revision
A
Amendment
4
Issue Date
May 13, 2004
This document contains information on a product under development at FASL LLC. The information is intended to help you evaluate this product. FASL LLC reserves the
right to change or discontinue work on this proposed product without notice.
A d v a n c e
I n f o r m a t i o n
General Description
The S29GL512/256/128N family of devices are 3.0V single power flash memory
manufactured using 110 nm MirrorBit technology. The S29GL512N is a 512 Mbit,
organized as 33,554,432 words or 67,108,864 bytes. The S29GL256N is a 256
Mbit, organized as 16,777,216 words or 33,554,432 bytes. The S29GL128N is a
128 Mbit, organized as 8,388,608 words or 16,777,216 bytes. The devices have
a 16-bit wide data bus that can also function as an 8-bit wide data bus by using
the BYTE# input. The device can be programmed either in the host system or in
standard EPROM programmers.
Access times as fast as 80 ns (S29GL128N, S29GL256N) or 90 ns (S29GL512N)
are available. Note that each access time has a specific operating voltage range
(V
CC
) and an I/O voltage range (V
IO
), as specified in the
Product Selector Guide
and the
Ordering Information (512 Mb)
sections. The devices are offered in a 56-
pin TSOP or 64-ball Fortified BGA package. Each device has separate chip enable
(CE#), write enable (WE#) and output enable (OE#) controls.
Each device requires only a
single 3.0 volt power supply
for both read and
write functions. In addition to a V
CC
input, a high-voltage
accelerated program
(WP#/ACC)
input provides shorter programming times through increased cur-
rent. This feature is intended to facilitate factory throughput during system
production, but may also be used in the field if desired.
The devices are entirely command set compatible with the
JEDEC single-
power-supply Flash standard.
Commands are written to the device using
standard microprocessor write timing. Write cycles also internally latch addresses
and data needed for the programming and erase operations.
The
sector erase architecture
allows memory sectors to be erased and repro-
grammed without affecting the data contents of other sectors. The device is fully
erased when shipped from the factory.
Device programming and erasure are initiated through command sequences.
Once a program or erase operation has begun, the host system need only poll the
DQ7 (Data# Polling) or DQ6 (toggle)
status bits
or monitor the
Ready/Busy#
(RY/BY#)
output to determine whether the operation is complete. To facilitate
programming, an
Unlock Bypass
mode reduces command sequence overhead
by requiring only two write cycles to program data instead of four.
The
Enhanced VersatileI/O™
(V
IO
) control allows the host system to set the
voltage levels that the device generates and tolerates on all input levels (address,
chip control, and DQ input levels) to the same voltage level that is asserted on
the V
IO
pin. This allows the device to operate in a 1.8 V or 3 V system environ-
ment as required.
Hardware data protection
measures include a low V
CC
detector that automat-
ically inhibits write operations during power transitions.
Persistent Sector
Protection
provides in-system, command-enabled protection of any combina-
tion of sectors using a single power supply at V
CC
.
Password Sector Protection
prevents unauthorized write and erase operations in any combination of sectors
through a user-defined 64-bit password.
The
Erase Suspend/Erase Resume
feature allows the host system to pause an
erase operation in a given sector to read or program any other sector and then
complete the erase operation. The
Program Suspend/Program Resume
fea-
ture enables the host system to pause a program operation in a given sector to
read any other sector and then complete the program operation.
2
S29GLxxxN MirrorBitTM Flash Family
27631A4 May 13, 2004
A d v a n c e
I n f o r m a t i o n
The
hardware RESET# pin
terminates any operation in progress and resets the
device, after which it is then ready for a new operation. The RESET# pin may be
tied to the system reset circuitry. A system reset would thus also reset the device,
enabling the host system to read boot-up firmware from the Flash memory
device.
The device reduces power consumption in the
standby mode
when it detects
specific voltage levels on CE# and RESET#, or when addresses have been stable
for a specified period of time.
The
SecSi™ (Secured Silicon) Sector
provides a 128-word/256-byte area for
code or data that can be permanently protected. Once this sector is protected,
no further changes within the sector can occur.
The
Write Protect (WP#/ACC)
feature protects the first or last sector by as-
serting a logic low on the WP# pin.
MirrorBit flash technology combines years of Flash memory manufacturing expe-
rience to produce the highest levels of quality, reliability and cost effectiveness.
The device electrically erases all bits within a sector simultaneously via hot-hole
assisted erase. The data is programmed using hot electron injection.
I am a beginner, but there are few books suitable for beginners on driver programming. Regarding variable declaration, if a variable is local, can it only be declared at the very beginning of the func...
I made a zero-crossing comparator using tlv3501 according to the data sheet. Theoretically, it has a bandwidth of 50M, but it fails when measured at 5MHz. I need some guidance....
Two projects are urgently recruiting two positions: Job content: 1) Participate in the company's embedded platform solutions and architecture, system design and development; 2) Engage in software requ...
This time I got a TI official LAUNCHXL-F280049C, the board comes with an XDS110 emulator, 280049 belongs to the Piccolo F28004x series
To use F280049C, you need to install a higher version of CCS, bec...
4.3 Jacobian Matrix The Jacobian matrix is widely used in various occasions. The Jacobian is the differential ratio of the output to the input, indicating the influence of the change (differential) of...
1. Overview
Will passive devices
produce nonlinear intermodulation distortion? The answer is yes! Although there is no systematic theoretical analysis, it has been found in engineerin...[Details]
In recent years, lighting has become an important area that countries around the world are targeting to promote energy conservation and environmental protection. According to statistics, about 20% ...[Details]
The concept of state machine
State machine is an important concept in software programming. More important than this concept is its flexible application. In a clear and efficient program, ther...[Details]
introduction
MEMS is a high-tech that has flourished on the basis of integrated circuit production technology and dedicated micro-electromechanical processing methods. Pressure sensors develop...[Details]
Abstract: The output of high-range acceleration sensor is less than 10 mV under the excitation of small signal. The noise of traditional test system may cover such small voltage signal, so that hig...[Details]
introduction
The core features of mobile value-added service products are mobility, immediacy and personalization. Mobile value-added services are a new service mode that is rapidly developing...[Details]
introduction
The Steyr diesel engine produced by Weifang Diesel Engine Factory has huge power and is one of the main power models widely used in China's heavy machinery and large trucks. In ...[Details]
TMC428 is a stepper motor motion controller from TRINAMIC. It can reduce the workload of motor control software design and development costs. The 3-axis stepper motor drive control system based on ...[Details]
Li/SOCl2 batteries (lithium sub-cells) have the advantages of high operating voltage, stable discharge voltage, wide operating temperature range and long storage life, and have been widely used in ...[Details]
Since the implementation of the self-weight toll collection system, the highway administration has not only high requirements for the vehicle axle recognition rate, but also requires a long service li...[Details]
The Portland Group, a leading provider of graphics processing units (GPUs) and graphics accelerators, has announced the availability of its PGI Accelerator™ Fortran and C compilers that support the...[Details]
Introduction
Zero-IF receivers are not new; they have been in use for some time, with cellular handsets being a key application area. However, their use in high-performance receivers such as...[Details]
According to a survey by the International Energy Agency, Asia and Australia used 1.65 trillion liters of oil for energy in 2004. The survey also showed that since 1990, the demand for oil has been...[Details]
0 Introduction
The traditional measurement method of measuring gravity acceleration by a simple pendulum in university physics experiments generally uses a mechanical stopwatch for manual timing and...[Details]
Semiconductor devices used in high-end computing (advanced microprocessors) and consumer electronics (graphics and gaming chipsets) devices generally provide data rates up to 6.4Gbps through high-s...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
