Above ratings are based on the thermal resistances using a multi-layer circuit board (EIA/JESD51). For mounting on a mono-layer board, power derating shall be
needed. Please inquire of us about conditions.
※1 素子毎の負荷電力の合計が、パッケージ定格電力を超えない条件で御½用ください。
※1 Total power consumption of all elements should not exceed the package power rating.
The resistor of this product is formed by narrow patterning a thin metal film. Thus, application of excessive voltage causes burn and destruction of the resistive film, abnormality
in resistance or open resistance and loss of proper function. The properly and electrostatically measured taping materials are used for the components, but attention should be paid
to the fact that there is some danger the parts may be destructed by static electricity(equivalent to 500V or over at 100pF, 1.5kΩ) to cause a change in resistance in the conditions
of an excessive dryness when mounting on the boards. Similarly, care should be given not to apply the excessive static electricity at the time of mounting on the boards. When
designing, consideration can be taken into withstanding ESD for customized KPC products. Please consult with us about the details.
●
Hand soldering by iron soldering or repairment are not recommended because KPC is a multi-pin product.
●
Avoid storing components under direct sun rays, high temperature/humidity. Direct sun rays will cause quality change of taping and difficulty of keeping appropriate peeling
strength. In the case of 5〜35℃/35〜75%RH, there is no deterioration of solderability for 12 months, but take special care for storing, because condensation, dust, and toxic gas
like hydrogen sulfide, sulfurous acid gas, hydrogen chloride, etc. may drop solderability.
Free sample application | Littelfuse relays, MOSFETs, sensors...no category restrictions, no quantity restrictions, come and apply!Click here to enter[Free sample dedicated channel][Must-read for appl...
In-depth analysis of Xilinx FPGA internal structureAuthor : fpga001 .Forum : Chip Power ( SocVista ).Structure of IOB
Please look at page 1 of the manual , which is the review section of IOB . IO bloc...
I want to make an infrared remote control, but I don't know how to design a circuit diagram. I hope someone with experience can give me a diagram for reference. Thank you in advance....
Requirements: Gender is not limited, those with experience in this field are preferred. College degree or above. Articulate. Salary: Negotiable Work location: Nanshan District Science and Technology P...
TI's battery experts have decades of experience. Our battery scientists work to deliver cutting-edge solutions for new battery chemistriestechnologies, from charging, gauging, monitoring to protection...
[i=s]This post was last edited by feiting94 on 2015-12-4 18:32[/i] [size=6]Friends who are still playing emwin, you can take a look at touchGFX,[/size][size=6]you can take a look at this effect[/size]...
Recently, the results of the 2018 German Red Dot Design Award were announced. GoodWe, a company located in Suzhou High-tech Zone, stood out among thousands of outstanding design products from 5...[Details]
In the war without gunpowder between China and the United States,
ZTE
has become a new victim. The seven-year chip ban by the United States has pushed this communications giant to a life-or...[Details]
1. Problem When developing STM32 with IAR, I found that I could not print floating point numbers by redirecting printf to the serial port. The code is as follows: The output is as follows: It can...[Details]
1. Test conditions Hardware: STM32L432KC Main frequency: 80MHz Compiler: IAR 8.20.1 Compiler options: High Speed no size constraints CRC generator polynomial: 0x782f 2. Test Method The softwar...[Details]
0. Preparation First use st-link to connect the stm32 core board and PC for burning St-link Stm32 3.3V 3.3V GND GND SWDIO PART SWCLK DCLK Then connect with USB serial port board to v...[Details]
China Energy Storage Network News:
The State Grid Corporation of China, this elephant, is planning to turn around and enter the emerging power service market.
The rallying cry for the tr...[Details]
As many companies listed with
the concept of
touch screen
begin to "transform and upgrade", the official voice of the TP industry is getting smaller and smaller. At the same time, the list o...[Details]
The application of millimeter wave technology in mobile communications also involves a series of technical problems, including the large propagation loss of millimeter waves and the susceptibility ...[Details]
In the Huaxing Optoelectronics LCD panel
factory
located in Guangming New District, Shenzhen
, apart from a few people repairing machines, it is often difficult to see other people. Here, ev...[Details]
Analysts have sorted out some interesting phenomena. Let's follow the embedded editor to learn about the relevant content.
Huawei emerged as a star in the all-
flash
array sales ra...[Details]
This program is used in the development board to generate sounds of different frequencies. The overall program is relatively simple, mainly using two timers. The code and my comments are as follows. ...[Details]
What is SYSTICK: This is a 24-bit system tick timer, SysTick, with automatic reload and overflow interrupt functions. All microcontrollers based on the Cortex_M3 processor can obtain a certain time ...[Details]
On the eve of 5G
commercialization,
ZTE
has established and adhered to
the
5G
pioneer strategy, focusing on
5G
end-to-end solutions, and investing in standard setting, ...[Details]
Independent watchdog (IWDG) and low power mode are often used in STM32 development. The watchdog is to detect and solve faults caused by software errors, and the low power mode is to enter sleep mode...[Details]
Discrete Device
京公网安备 11010802033920号
EEWORLD
