EEWORLDEEWORLDEEWORLD

Part Number

Search

Y1626160R000A9W

Description
Fixed Resistor, Metal Foil, 0.3W, 160ohm, 95V, 0.05% +/-Tol, -.2,.2ppm/Cel, 1506,
CategoryPassive components    The resistor   
File Size838KB,6 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Environmental Compliance
Download Datasheet Parametric View All

Y1626160R000A9W Overview

Fixed Resistor, Metal Foil, 0.3W, 160ohm, 95V, 0.05% +/-Tol, -.2,.2ppm/Cel, 1506,

Y1626160R000A9W Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid860431359
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresNON INDUCTIVE; ULTRA HIGH PRECISION
structureRectangular
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package height0.64 mm
Package length3.81 mm
Package formSMT
Package width1.57 mm
method of packingWAFFLE PACK
Rated power dissipation(P)0.3 W
Rated temperature70 °C
resistance160 Ω
Resistor typeFIXED RESISTOR
size code1506
surface mountYES
technologyMETAL FOIL
Temperature Coefficient0.2 ppm/°C
Terminal surfaceTin/Silver/Copper - with Nickel barrier
Terminal shapeWRAPAROUND
Tolerance0.05%
Operating Voltage95 V
VSMP Series(0603,0805,1206,1506,2010,2010,(ZFoil)
VSMP Series (0603, 0805, 1206, 1506, 2512) 2512)
(Z Foil)
Ultra High Precision Foil Wraparound Surface Mount Chip Resistor
with TCR of ±0.05 ppm/°C and Power Coefficient of 5 ppm at
Rated Power and Load Life Stability of ±0.005% (50 ppm)
FEATURES
• Temperature coefficient of resistance (TCR):
0.2 ppm/°C typical (–55°C to +125°C, +25°C ref.)
• Resistance tolerance: to ±0.01%
• Power coefficient “∆R due to self heating”:
5 ppm at rated power
• Power rating: to 750 mW at +70°C (see table 3)
• Load life stability: to ±0.005% at 70°C, 2000 h
at rated power
• Resistance range: 5 Ω to 125 kΩ (for lower or higher
values, please contact us)
• Bulk Metal Foil resistors are not restricted to standard
values, we can supply specific “as required” values at
no extra cost or delivery (e.g. 1K2345 vs. 1K)
• Thermal stabilization time <1 s (nominal value achieved
within 10 ppm of steady state value)
• Electrostatic discharge (ESD) at least to 25 kV
• Short time overload: ≤0.005%
• Non inductive, non capacitive design
• Rise time: 1 ns effectively no ringing
• Current noise: 0.010 μV
RMS
/V of applied voltage
(<–40 dB)
• Voltage coefficient <0.1 ppm/V
(resistance values above 10 kΩ)
• Non inductive: <0.08 μH
• Non hot spot design
• Terminal finishes available: lead (Pb)-free, tin/lead alloy
• Matched sets are available on request
• Screening in accordance with EEE-INST-002 and
MIL-PRF-55342 available (see datasheet resistor
models 303133 to 303138)
• Quick prototype quantities available, please contact
foil@vpgsensors.com
Top View
(for date code print specification please refer to table 2)
INTRODUCTION
VSMP Series is the industry’s first device to provide high
rated power and excellent load life stability along with
extremely low TCR – all in one resistor.
One of the most important parameters influencing stability
is the Temperature Coefficient of Resistance (TCR).
Although the TCR of Bulk Metal
®
Foil is considered
extremely low, this characteristic has been further
refined over the years. The VSMP Series utilizes ultra
high precision Z Foil. The Z Foil technology provides a
significant reduction of the resistive element’s sensitivity
to ambient temperature variations (TCR) and to self
heating when power is applied (Power Coefficient of
Resistance, or PCR). Along with the inherently low PCR
and TCR, Z Foil technology also provides remarkably
improved load life stability, low noise and tight tolerances.
Vishay Foil Resistors’ (VFR) application engineering
department is available to advise and make
recommendations. For non-standard technical
requirements and special applications, please contact
us using the e-mail address in the footer below.
Table 1—Tolerance and TCR vs. Resistance
Value
(1)
(–55°C to +125°C, +25°C Ref.)
Resistance value
250 Ω to 125 kΩ
100 Ω to <250 Ω
50 Ω to <100 Ω
25 Ω to <50 Ω
10 Ω to <25 Ω
5 Ω to <10 Ω
(1)
Figure 1—Power Derating Curve
Percent of Rated Power
100
75
50
25
0
- 75
Tolerance
±0.01%
±0.02%
±0.05%
±0.1%
±0.25%
±0.5%
Typical TCR and
max. Spread
±0.2 ±1.8 ppm/°C
±0.2 ±1.8 ppm/°C
±0.2 ±2.8 ppm/°C
±0.2 ±3.8 ppm/°C
±0.2 ±3.8 ppm/°C
±0.2 ±7.8 ppm/°C
- 55 °C
+ 70 °C
For tighter performances and non-standard values lower than
5 Ω and above 125 kΩ, please contact application engineering
using the e-mail addresses in the footer below
- 50
- 25
0
+ 25 + 50 + 75 + 100 + 125 + 150 + 175
Ambient Temperature (°C)
* This datasheet provides information about parts that are RoHS-compliant and/or parts that are non-RoHS-compliant.
For example, parts with lead (Pb) terminations are not RoHS compliant. Please see the information/tables in this datasheet for details.
4128-EN
Rev 04-Mar-2020
For any questions, contact
foil@vpgsensors.com
www.vishayfoilresistors.com
1
Don't move! Let me take a quiet and beautiful photo [Support Impression Test Video Contest]
[font=微软雅黑][size=4]I saw this a few days ago and I think it’s very creative. I happened to come across the forum’s [/size][/font][size=4][url=https://bbs.eeworld.com.cn/thread-484812-1-1.html]>>KEYSIG...
nmg Talking
Help with remote control of stepper motor based on sim300 (or tc35) and stc52 microcontroller
This forum is really good. I browsed through almost all the microcontroller sections in one breath. I even lost interest in the relay protection course design I am doing. I really want to collect all ...
yuemiss MCU
51 single chip digital tube serial communication
I want to ask whether the 51 single-chip microcomputer can realize that different digits of the digital tube light up different digits at the same time. If the serial communication is used to input nu...
余生798 51mcu
When converting to GERBER, should I check the option "include unconnected mid-layer pads"?
When converting to GERBER in Altium Designer 14.3, should I check the option of include unconnected mid-layer pads? I have drawn two signal layers in the middle of a four-layer board. I used to send t...
zttian PCB Design
Modified based on SampleApp example, the first byte of the data read from the computer serial port is garbled.
Hardware is fine I switched from ZSTACK 2.2 to ZSTACK 2.5 Found this problem, the first character received is garbledNormal in ZSTACK 2.2 The following characters are normal Please help me, thank you....
高兴就好 RF/Wirelessly
Lack of understanding of some professional terms
I often visit forums, and I don't quite understand some of the professional terms mentioned by the masters in their answers. 1: Initialize the stack. Is the following code initializing the irq stack? ...
bin8888 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 742  2626  332  2696  1853  15  53  7  55  38 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号