5962-8954102CX datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> Amplifier circuit> 5962-8954102CX

5962-8954102CX: DescriptionSample and Hold Circuit, 1 Func, Sample, CDIP14, CERAMIC, DIP-14; CategoryAnalog mixed-signal IC Amplifier circuit; File Size40KB，11 Pages; ManufacturerADI; Websitehttps://www.analog.com

Download Datasheet Parametric View All

5962-8954102CX Overview

Sample and Hold Circuit, 1 Func, Sample, CDIP14, CERAMIC, DIP-14

5962-8954102CX Parametric

Parameter Name	Attribute value
Objectid	2082023763
package instruction	CERAMIC, DIP-14
Reach Compliance Code	unknown
Amplifier type	SAMPLE AND HOLD CIRCUIT
Maximum analog input voltage	10 V
Minimum analog input voltage	10 V
maximum rate of descent	2 V/s
JESD-30 code	R-GDIP-T14
Negative supply voltage upper limit	-18 V
Nominal Negative Supply Voltage (Vsup)	-15 V
Number of functions	1
Number of terminals	14
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
Package body material	CERAMIC, GLASS-SEALED
encapsulated code	DIP
Package shape	RECTANGULAR
Package form	IN-LINE
Certification status	Not Qualified
Sample and hold/Track and hold	SAMPLE
Supply voltage upper limit	18 V
Nominal supply voltage (Vsup)	15 V
surface mount	NO
Temperature level	MILITARY
Terminal form	THROUGH-HOLE
Terminal location	DUAL

Preview

Download Datasheet

View All

REVISIONS

LTR

DESCRIPTION

Drawing updated to reflect current requirements. - ro

DATE (YR-MO-DA)

01-05-15

APPROVED

R. MONNIN

THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.

REV

SHEET

REV

SHEET

REV STATUS

OF SHEETS

PMIC N/A

REV

SHEET

PREPARED BY

RICK OFFICER

STANDARD

MICROCIRCUIT

DRAWING

THIS DRAWING IS AVAILABLE

FOR USE BY ALL

DEPARTMENTS

AND AGENCIES OF THE

DEPARTMENT OF DEFENSE

CHECKED BY

CHARLES E. BESORE

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43216

http://www.dscc.dla.mil

APPROVED BY

MICHAEL A. FRYE

MICROCIRCUIT, LINEAR, LOW-DROOP-RATE,

ACCURATE SAMPLE AND HOLD AMPLIFIER,

MONOLITHIC SILICON

DRAWING APPROVAL DATE

89-08-15

AMSC N/A

REVISION LEVEL

SIZE

SHEET

CAGE CODE

67268

1 OF

5962-89541

DSCC FORM 2233

APR 97

DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.

5962-E419-01

1.4 Recommended operating conditions.

Positive supply voltage range (+V

) ...................................... +15 V dc

Negative supply voltage range (-V

) ...................................... –15 V dc

Hold capacitor (C

) ................................................................ 0.005

µF

Logic control (V

) ................................................................. Connected to ground, or 3.5 V below positive supply

and 2.0 V above negative supply

Ambient operating temperature range (T

) ............................ -55°C to +125°C

2. APPLICABLE DOCUMENTS

2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a

part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed

in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in

the solicitation.

SPECIFICATION

DEPARTMENT OF DEFENSE

MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.

STANDARDS

DEPARTMENT OF DEFENSE

MIL-STD-883 -

MIL-STD-1835 -

HANDBOOKS

DEPARTMENT OF DEFENSE

MIL-HDBK-103 -

MIL-HDBK-780 -

List of Standard Microcircuit Drawings.

Standard Microcircuit Drawings.

Test Method Standard Microcircuits.

Interface Standard Electronic Component Case Outlines.

(Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization

Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text

of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a

specific exemption has been obtained.

3. REQUIREMENTS

3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-

JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer

Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-

PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying

activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan

may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device.

These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MIL-

PRF-38535 is required to identify when the QML flow option is used.

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43216-5000

DSCC FORM 2234

APR 97

SIZE

REVISION LEVEL

5962-89541

SHEET

3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as

specified in MIL-PRF-38535, appendix A and herein.

3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.2 herein.

3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.

3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are

as specified in table I and shall apply over the full ambient operating temperature range.

3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical

tests for each subgroup are described in table I.

3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN

listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked as listed in MIL-HDBK-103 (see 6.6 herein). For

packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the

option of not marking the "5962-" on the device.

3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance

to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification mark in

accordance with MIL-PRF-38535 to identify when the QML flow option is used.

3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an

approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to

listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-PRF-

38535, appendix A and the requirements herein.

3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided

with each lot of microcircuits delivered to this drawing.

3.8 Notification of change. Notification of change to DSCC-VA shall be required in accordance with MIL-PRF-38535,

appendix A.

3.9 Verification and review. DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's

facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the

reviewer.

4. QUALITY ASSURANCE PROVISIONS

4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535,

appendix A.

4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices

prior to quality conformance inspection. The following additional criteria shall apply:

Burn-in test, method 1015 of MIL-STD-883.

(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision

level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall

specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in

test method 1015 of MIL-STD-883.

(2) T

= +125°C, minimum.

Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter

tests prior to burn-in are optional at the discretion of the manufacturer.

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43216-5000

DSCC FORM 2234

APR 97

SIZE

REVISION LEVEL

5962-89541

SHEET

Recommended Resources

Fixed 5V (1A) switching regulator circuit diagram

Vibration frequency measurement optical fiber sensing signal same frequency detection circuit

Two kinds of CMOS system DC motor control switching circuits

300W high-fidelity amplifier circuit

820e computer motherboard circuit diagram_11

Video amplifier circuit: TDA6103

Apple's driverless test car gets upgraded with radar sensor: [p=26, null, left][color=rgb(43, 43, 43)][font=SimSun][size=14px] According to the British Daily Mail on August 28, Apple's driverless car recently appeared at the test center in Sunnyvale, California...; fish001 RF/Wirelessly

2.5V voltage regulator circuit: As shown in the figure above, refer to the information on the Internet. If you want a circuit with an input of 2.5V-12V and an output of 2.5V, the circuit implementation principle is: after power-on, ...; 小魏哥哥 Switching Power Supply Study Group

What upgrades are there for cortex-M4 and cortex-M4F?: From the above figure, we can see that the cortex-M4 has a Floating-Point Unit (FPU) and DSP more than the previous generation cortex-M3 . 1. DSP must be supported in cortex-M4.2. FPU is an optional f...; Jacktang DSP and ARM Processors

How to instantiate global clock resources: There are two ways to instantiate global clock resources: one is to instantiate global clock resources directly in the program; the other is to use global clock resources through synthesis stage const...; eeleader FPGA/CPLD

Sensor topic (one more): [i=s]This post was last edited by paulhyde on 2014-9-15 04:25[/i] Let's work together...; titian361646 Electronics Design Contest

How can we achieve Figure 1 to Figure 2?: [backcolor=rgb(239, 245, 249)]As the title says, I want to process the waveform in Figure 1 to achieve the effect in Figure 2. What method can be used to achieve this? [/backcolor] [backcolor=rgb(239,...; zhaironghui DSP and ARM Processors

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components