Only channels 0 and 1 can be used for reception. If EN_RXADDR is configured as multi-channel (0x03), it is not acceptable. I have been struggling for a long time. Please give me some advice!
Part of t...
After the heavy snow in Texas, the production capacity of many international manufacturers in China was severely affected, and the shortage of MCU chips was once again aggravated. This is undoubtedly ...
The ADC clock source is set to SMCLK=25MHz, divided by 5, that is, 5MHz, the sampling and holding time is 4 ADC clock cycles, 12-bit accuracy, and the conversion time is 13 cycles, which is more than ...
Shenzhen Programmer QQ Group Alliance has been established for more than two years and has more than 30 QQ groups with more than 2,000 members. Now it is full of heroes, among which the Shenzhen Progr...
0. Preparation First use st-link to connect the stm32 core board and PC for burning St-link Stm32 3.3V 3.3V GND GND SWDIO PART SWCLK DCLK Then connect with USB serial port board to v...[Details]
Artificial intelligence
There is no inherent bias in AI. It does not "think" something is true or false for reasons that cannot be explained by logic. Unfortunately, human bias exists in mach...[Details]
At the just concluded InfoComm 2018 exhibition, the two major brands, Zhongke Jiguang and China Hualu, both displayed three-color light source
laser TVs
. The outstanding color performance ...[Details]
This routine is also a classic routine on the development board. I modified the framework of the program to make it more suitable for future calls. The specific 4*4 keyboard scanning principle is rel...[Details]
In the project, CPLD is needed to complete part of the algorithm design. The parameters are given by AVR, so the communication between AVR and CPLD needs to be completed. Therefore, a test program is...[Details]
The day before yesterday, another mainland technology company submitted a prospectus to the Hong Kong Stock Exchange. The company is called "Jia Nan Creative (hereinafter referred to as 'Jia Nan')"...[Details]
Use the STM32 timer input capture module to control 3-way ultrasonic sensors. The ultrasonic sensor used this time is the common HC-SR04, which is often used in the obstacle avoidance system of smal...[Details]
Here is the temperature added in the previous chapter The above figure is the temperature calculation formula: where Vsense is the ADC value collected from the temperature channel. The stm32f407 ...[Details]
The T3 timer (8-bit) of CC2530 requires understanding of T3CTL, T3CCTL0, T3CC0, T3CCTL1, and T3CC registers. Timer 3/4 is an 8-bit timer with timer/counter/PWM functions. Timer 2, also known as MAC t...[Details]
The key is the configuration of registers. The T1 timer (16 bits) of CC2530 needs to configure three registers: T1CTL, T1STAT, IRCON Here is just a brief introduction. For more details, please refer ...[Details]
One addend is in the on-chip RAM 40H, 41H, 42H units, the other addend is in the on-chip RAM 43H, 44H, 45H, and the sum is stored in the 50H, 51H, 52H units, with the carry bit stored in 00H. Please ...[Details]
MCS-51 single-chip microcomputer timer/counter experiment programming program Programming requirements: 1. Connect a light-emitting diode LED to the P1.0 pin, light up for two seconds, turn off for o...[Details]
By manually inputting single pulses to the /INT0 of the 8051 microcontroller one by one, an interrupt is requested to the microcontroller. Each time the microcontroller interrupts, it outputs 55H, AA...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
